I am having trouble with the connection between one of our Cisco Air-Cap-1602E (Autonomous Mode) indoor access points disconnecting from our Cisco air-cap-1552E Lightweight Access point. We have a WLC 5508, and a WGB set up for these AP's to connect...
Forum Posts
Is there any way to integrate Thousand Eyes with Meraki if we are only using Meraki access points?
Hello Cisco WLAN-experts,after upgrading a 9800-L-C from 17.3.6 to 17.12.6a I noticed a Telemetry alarm on Cisco Prime:Catalyst 9800 telemetry coral connection failureOn the 9800-L-C I can seen the following broken pipe problem:WLC-9800-Guest#show t...
QSC sells mixers (such as the TouchMix-30) that work with companion iOS app. The app can only connect the mixer by finding it via Bonjour.In the template assigned to the network, on a group policy that gets assigned to me via 802.1X, I configured a B...
Resolved! EWC 9120 WITH ISE
Hi we have an AP 9120 which is used as our controller (EWC) , we want to connect it to ISE, is it supported ? and do we need a specific version ? Thanks
Hi everyone, I am facing a persistent issue enabling IOX and Advanced BLE on C9136I-ROW access points. We require this feature for Asset Tags and tracking. Current Environment: WLC Version: 17.18.2 (Upgraded from 17.15.4b per TAC recommendation to fi...
Buenas tardes, me acaba de llegar un caso donde usuarios de apple acaban de actualizar sus iPhone a la versión de iOS 26 y después de esta versión ya no tienen navegación. No sé si hasta el momento han visto un comportamiento similar con esta versión
Hello Community,I am using cisco WLC 9800 and WLAN is configured to use Local dot1x authentication.where can i see the local users configured for this authentication.from GUI i am not able to find the local users section for this.Thanks in advance.
I have upgraded the firmware and successfully setup site-survey. The SSID is broadcasting, but I cannot login to the gui after setting up site-survey on a C9136I AP - admin/admin, Cisco/Cisco doesn't work. I factory reset the Ap and started over and ...
Trying to figure out the best way to set up a Cisco 3802E AP for our WLC environment. I was able to connect it to our WLC, but then noticed no Bridge/mesh option in WLC settings. Would be using this AP indoors, with external antenna above structure ...
Hello All,Greetings!I am planning to have a SSID named SSID1 & VLAN group range 201 to 205 assigned to this SSID in WLC C9800. among these vlan I want VLAN 201, the devices I want to assign IP statically should fall in this VLAN. 202 to 205, the devi...
I have 3 SSIDs configured [ Staff, Student and Guest]. I have applied web filtering on Student and Guest SSIDs as below but Staff users are also facing issues on browsing and sending messaged on Whatsapp. There is no restriction on SSID Staff. Not al...
Hi, one of my 2802i refuses to join my WLC. On console all CAPWAP config commands fail with "Capwap process not ready yet. Try after few moments." AP00F2.8B27.AD68#show capwap client config AdminState : ADMIN_ENABLED(1)Name : AP00F2.8B27.AD68Locati...
Hello all. I work at a K-12 School district and we just received several Chromecasts with Google TVs and I'm having trouble getting them to work. My windows laptop (Lenovo L13 Yoga) and Chromecast are both on the same wireless network and I can see t...
Hi,Recently handle a project realted with mDNS(Bonjour) transfer.It's same VLAN#1mDNS packet from wireless client to multicast address can be captured on wired server.#2mDNS oacket from wired server cannot be captured on wireless client, but on the A...
