Hi,We have installed Cisco RV340W dual WAN Wireless-AC VPN Router in our office but since it start day the wifi freeze in few days regularly. Previously we thought it was due to update but even after disabling the update and firewall the error persis...
Forum Posts
Hi comunnity,I'm facing some connectivity issues when trying to connect iPhone 6 running any iOS 12.4.x release.They all get stuck after receiving 4-way handshake M1 and after many retries, the controlelr delete the session. See below RA output:{wncd...
Hello Experts @Scott Fella @Sandeep Choudhary @Rob Ingram I got cisco WLC and I can only connect to it if my computer is in same network. I tried changing its IP and vlan and even within new vlan, I am only connect to it if my laptop connected ...
some of ap will re-jion my ACmy AC logs: Time: Oct 15 14:03:41Facility: local0Priority: emergTag: BHKJ_WLCMessage: *broffu_SocketReceive: Oct 15 14:05:55.051: %BROFFU-0-DP_PACKET_WQE_DIFF: broffu_fp_dapi_cmd.c:6348 Warning: DP Packet pool and WQE poo...
Hi,I´d like to as a Design-related question regarding the general positioning of a Wireless LAN Controller- and ISE NAC appliance in a network!Would it be necessary/useful to secure respectivly the Wireless LAN Controller and/or the ISE from the rest...
Hi, I am trying to configure a vlan group with 2 vlans (10-11) for ssid on 5760 controller. I can't see client is taking ip address from the second vlan . it always get the ip address from the vlan 10 I thought it randomly get ip addresses from ...
iseHello Team.We have C9800 with Wave 2 AP in flex mode.We are trying to implement SGACL enforsment for local switched traffic. I see SXP connection with ISE. But SGACL enforsment doest work. But in C9800 GUI in AP page, trustsec tab i see that (s...
Hi, I'm looking for guidance in building out a solution for a portable wireless network for tactical use. FIPS 140-2 compliant60-120 users with 500ft signal rangeOperate in -20F to 150F temperaturesInclude physical cat5 ports I don't have much networ...
Resolved! Basic/Mandatory Data Rates
What are the trade offs for setting the Mandatory Data rates for radios too high? In my own past experience have only configured mandatory rates to be somewhat leniently (ex 6mb on 2.4ghz b radio or 24mb on a 5ghz a radio). Recently came into a case ...
Hi everyone, I'm looking for instructions on how to renew a cert that will be expiring on my wireless controller next week. I have read all the guides that tell you how to install a 3rd party cert, how to generate and download a CSR, etc. But no guid...
Resolved! full info about HA WLC-3504
Hello for everybody. Is it possible to find full info about HA from two wlc-3504, using cli.I need to know serial and mac address of the second wlc in ha. When i connect to main wlc, using cli i can see only info rom main wlc, but not for second one.
I have a IR1101 with a P-LTE-VZ module coming. I need to get an OMNI type outdoor antenna, antenna cable, and lightning arrestor for this install. I cannot find documentation on the type of antenna connection that is on the module. I'm believe that i...
Hello Community,We have an SSO HA implementation with 2x 5520 (both AIR-CT5520-K9), software version 8.5.151.0.License for 100 APs, 96 APs in use.When we simulate a problem by powering off the Active Controller, the standby controller will reboot, al...
No, really! Not only are we sponsoring an incredibly cool autonomous version of the Indy 500, but all kinds of Cisco technology is actually in the cars, and helping the students that built them, run the race. The autonomous vehicles are able to re...
I use WLAN templates in Cisco PI 3.8 to setup WLAN SSID's across a few campuses where I need to change the SSID quite often. Is there a way to enable the 11K Neighbor List in the PI WLAN template? I can't find it as an option... I need to goto al...
