Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi all My Access Point is using local mode and I configured interface group for VLAN Select. But somehow I need to change the AP from local mode to flexconnect, but seems the WLAN to VLAN mapping in flexconnect group is a 1:1 mapping. May I the Flexc...
Hi all,I am trying to add an Aironet 1830 AP to a Controller/Group of AP that are already under ME. I understand you can have capwap one working with it, without converting it yo ME. The only thing will be not having it being able to be a master or p...
Hello Cisco WLAN experts,we are running a 9800-L-C as Guest-WLC not only for a new 9800-80 but also for two 5520-WLC.When I look into the log of the 9800-L-C I can see a lot of messages of this kind containing mobility 0000.0000.0000%MM_INFRA_LOG-3-M...
Hi there,Mounting a new AP and was wondering if there is a recommended position to mount it.Is there any difference if mounting it vertically or horizontally etc?Is there a specific direction/angle the waves a propagating or is kind of 360?Thanks for...
Hi All,I have just been able thanks to your help as well to add a new AP to a set of AP under ME.As a general recommendation, I would like your feedback on whether especially after adding a new AP is recommended to do a RF tuning or other config chec...
Hi all there,quick question if anyone has been through this already or if you are aware of anything to this regard.We are temporarily using a set of Cisco Aironet 1830 AP all running Mobility Express and 1 acting as WLC. Normally they are set on Cisc...
Hello, everyone.Do we have a Cisco Catalyst 9800-CL Wireless Controller17.9.2, which is accusing vulnerability (NTP Information Disclosure Vulnerability), has anyone applied the fix on a WLC for this case? Could we help?
Hi, I need to disable redundancy on the active WLC for some reason. However, when I try to apply the config after disabling the redundancy, it gives me a warning saying "Clearing the chassis HA configuration will result in both the chassis move into ...
Have several sites where we installed AIR-AP3802I-B-K9 (Primary and IOS versions are 17.3.6.76) connecting back to Cisco Catalyst 9800-L (17.3.6) via AT&T MPLS (Ap is attached to Cisco switch which is connect to ATT Anira device which routes back to ...
Dear All,I am trying to setup an IPSEC Tunnel between a WLC 5508 and a ISE, to perform AAA with radius protocol.I' d like setupo a IPSEC tunnel and let the radius data from the wlc to ISE pass inside it.I have configured the WLC Radius profile enabli...
As a tittle suggests, AP failed to join to WLC (C9800) after first booting. The other day, we stopped the power of AP because of planned power outage. After finishing that and AP was power on, AP failed to join to WLC (C9800). A long time ago, We cha...
Hi everyoneI am absolutely new to Cisco Spaces, but I was able to set it up with a Cisco Spaces Connector and have imported the Network Hierarchy from Cisco DNA Center to Cisco DNA Spaces.Now I am looking for a specific use case:~7’000+ employees~17’...
Hello, running software 17.9.2, and tried to install "Hitless recomended SMU, CSCwd87612, dated 23-Dec-2022.Uploaded and did a commit, but nothings happen.The status is "Upgraded and Not Impacted".What does this mean ? Any suggestions ?Upgrade statis...
Hello,I am interested in receiving alerts via SMS I found this URL:https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Alerts_and_Notifications#Receiving_Email_Alerts_via_SMSHere it says that this is the AT&T syntax: phonen...
Resolved! ACI and CCI
Hi there are two APs with the same wlc. When AP1 uses channel 1 and AP2 uses channel 6 or 11 with 2.4. Can we say ACI and CCI do not happen no matter how close the two AP are? Thanks
