HiHave a 1602I AP in Autonomous mode. (ap1g2-k9w7-tar.153-3.JF15.tar)How do I erase/delete to factory reset?
Forum Posts
Hi,I have a 3702, runing as a uWGB, connected to a Third Party AP. I was wondering if I could shove a switch behind it, and add more than one client, using the MAC Address of the switch? Also would vlans pass through?
I'm trying to configure an ACL on Catalyst 9800 vWLC GUI but I can't figure out why there isnt'a a 'any' option for ports and protocols in extended ACLs? Default value for protocol field is adp and for source or destination port is None. Will None wo...
This "config network secureweb cipher-option high enable" command is enable HTTPS on WLC version 8.5.x but i don't know about this commands in WLC 9800 I found a security vulnerability follow detail on below.- TLS/SSL Weak Message Authentication Cod...
Everythnig worked fine in our Wi-Fi until the WLC (8500 with 8.0.133.0) was updated and moved to another physical location (another country). Since then, Android devices (quite old 2.3 Androids and some newer Android 4) are often disconnected (must r...
Hi there,currently reviewing settings of a set of AP under MobilityExpress/WLC and wondering :- what are the best/ideal settings to have/implement across the AP (I understand this depends on situations etc but generally...)- current update is 8.10.16...
Can a Cisco 9100 Series EWC working side by side with another WLC within the same network?Hi, I'm very new about cisco products and don't have enough knowledge about wireless controller. I have a project with a Cisco 5508 WLC and 10 pieces 9115 Acces...
cisco 3802i flashing red then green. unable to ping
Resolved! Setting Syslog Notifications on WLC
Where do you actually set the syslog on the C9800 WLC (in our case an EWC)?I see something under Administration > Management > Logging but that doesn't seem to workThen there is something under Configuration > Tags & Profiles > AP Join > ap profile >...
Have an SSID that is configured for WPA2-Enterprise using Radius/802.1x-PEAP. 802.11w is set to required. SSID is running in NAT mode.At times I am seeing errors like the following:Client made an 802.1X authentication request to the RADIUS server, bu...
I am deploying another pair of 1562D to create a redundant wireless connection to the remote building and also achieve aggregate throughput. The 1562 are lightweight that connect to a 5520 WLC. The WLC is running code 8.10.181.0 and the 1562's are ...
Resolved! Reboot multiple APs simultaneously
Hello Everyone, It's probably been asked before, but I was wondering if there was a way via the Dashboard to reboot APs multiple simultaneously.I know the TAC engineers can do it, but I didn't know if they added the feature for regular Network Engine...
how do i fix a mac address from chromecast with SSID its have a authen to use wifi.my problem is first i can connect chromecast with wifi but when i re-open chromecast it can't connect wifi anymore. so i cant cast screen.i can login console meraki.
We are pushing traffic using a packet generator on a client at a rate of 10Mbit/s via a Cisco AP C9120AXI-E.Using the following command we can fetch the BSSID counters form the WLC9800.show wireless stats ap name AP8C1E.8025.7D7C dot11 5ghz slot 1 wl...
Hello Cisco WLAN-experts,after upgrading a HA-pair of 9800-L-C from 17.3.5b to SW-version 17.3.6 we noticed that the ServicePort-Interface Gi0is no longer working. I was connected via its IP-adress during the ISSU-upgrade.As soon as the former Standb...
