Hi!One 5520 WLC running 8.5.x and the other one is running 8.10.181.Is it possible to start a mobility group between these? the 5520 with 8.10.181 is running 9120 APs, and the one with 8.5.x is running som 2600 APs.We will change all 2600 model to 91...
Forum Posts
I have 240 AP's on a 5508 controller. The AP's are at 12 different locations and they all stay associated except for one location. This location has 2 AP's and when they lose the association with the controller it is always both AP's at the same time...
Dear All, Would like to seek for help on the following, one of our customer are using Meraki MR44 AP, and with 2 ssid created call "Internal" & "Visitor", ssid internal are authenticated with Radius server, and ssid visitor are authenticated via PSK,...
Resolved! Meraki AP auth error
Kindly inform us what will be the main reason of following authentication errors of meraki AP's connection logs. I'm using MR33 APs.1.Client failed during the authentication step.(reason='reserved' radio='0' vap='0' channel='11' rssi='47)2.reason='ea...
I have AIR-AP1242AG-S-K9 standalone access point. It has radius server group configured but no radius server configured under the group. But still it authenticates the users. I'm trying to figure out how it authenticate the users. Below is the output...
Hey there,I'm wondering what the default settings are for:Wireless > Radio Settings > RF Profiles > Basic Indoor Profile > 5GHzRadio transmit power range (dBm)This is a range, so there are two values, one to the left and and one to the right. Transmi...
Hi, can someone help me with the mac filtering concern. We have C9800 and broadcasting a multiple SSIDs and those SSIDs are using same authentication MacAuth. However when I add the client mac address and point to certain SSID, device is also able to...
Resolved! MR 44 goes into repeator mode
Dear All, 2 of our MR44 AP goes into repeator mode, having check in to meraki switch side and run a cable test button, the pair 4 show open, does it means it is related with bad cable issue ? having checked the Poe useage, it is still under usage, an...
We have recently moved an office between floors in a building.We are still waiting for the ISP to shift the main circuit and are are currently running on a 5G router.Before we moved the Meraki clients to connect to the 802.1X SSID ok. But since movin...
Hi, I have cisco access points models 1602i and 1802i and want to purchase cisco 9800-cl controller.Does these access points are compatible with and can join the controller or must change the access points to new one?Thanks.
Hi, I've question about Prime Infra report - Associated and authenticated count Because my customer has PI and CMX running.When they generated report, they have notice Visit hourly trend are different with PI assoc/authen hourly count even in the sam...
Hello, I am quite new with mobility express and I would like to configure native vlan on Mobility express management interface. I used the following command and see that vlan is changed to 10. (Cisco Controller) >config interface vlan management 10 B...
Resolved! Guest bandwidth limit
I need advice to limit the bandwidth for our guest users. Meraki school with 180 APs (MR56) 500Mb up down. Question, what would be the best recommended settings to allow a maximum of 100Mb to the guest users without affecting client performance.Curre...
Hi,Have a problem of join a CAP1532 to a WLC2504, the two devices could ping each other and on 2504 I could see the AP in the ap join statistics, but it seems like the AP does not receive the response from WLC.I configured both DHCP and DNS, tried us...
Resolved! 9800-CL VM Deployment Failing
Hi, I am setting up a home LAB and attempting to deploy 9800-CL as VM. However, the installation is repeatedly stuck as depicted in the image below, I have left it for several hours but the installation does not progress. I have also downloaded and a...
