Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have somequestions, I saw access points high up in the middle of the roof, how high can you have access points normally and still get a decent signal ? They were about 25m high I would saysecond, how many users per ap is recommended? I hear about 6...
Hello Team,i would like to rename the WLC and assign a new IP address to the device. is there anything to consider when doing this. For example certificates and so on.thanksalex
Hi Cisco Family,I am having a lot of issues having HA formation on WLC 9800 - CL V 17.3.4c Amsterdam.It was working when both VMs were on the same hypervisor , but when we migrated the Primary to the Active DC , Since then i could not get HA bacK. To...
I am having big issues with a migration in which I moved some 3802 APs from a 5500 series WLC to a 9800 series. They were happy enough to join, but now I am plagued by them dropping and rejoining over and over. Here is a snippet of examples of this:0...
Dear guys. I'm looking for a sim based portable router that can be connected to the internet (3g/4g) and supply internet connection to up to 40-50 devices (smartphones), in a range of around 40 meters (130 feet). I need it for a group of travelers...
A mobility express ap (K9c) can control a CAPWAP ap (K9) ? help me!
Resolved! wireless Qos config at switch
Hi we have wireless 9800 system. APs are connected to C9300 switch. The client would need some meeting via MS Team etc at their PC or laptop. In the configuration of switch port connected AP, we have several choices as below. Which one is better for ...
Hello All,We have a Cisco AireOS 8.3 anchor foreign setup with Cisco 2500 WLCs which is used for guest client authentication with an external captive portal and radius server yields in the cloud. Radius server should dynamically determine the public...
Hi, I'm trying to connect AP to WLCBut I think firmware compatible doesn't match.AP : Air-AP1142N-K-K9c1140-k9w8-mx.153-3.JC8/c1140-k9w8-xx.153-3.JC8 WLC : WLC 25048.2.160.0 Am I have to do upgrade/downgrade of WLC or AP?If I need to do, where I can ...
On the datasheet for the Meraki Dual Band Patch Antenna MA-ANT-25• https://meraki.cisco.com/lib/pdf/meraki_datasheet_antenna_dual_band_patch_8dBi_6dBi.pdfthere are diagrams of the Signal Coverage Patterns, which consist of polar coordinate graphs -- ...
I want to use AD authentication in the Splash page, but want to limit the access to a specific AD group rather that the cumbersome AD scoping mentioned in the documentation.How can that be accomplished?I can use LDAP in the Splash page if that is wha...
Resolved! IOS-XE 9800 SSH to APs
Hello wireless experts,I understand, that the AP SSH access is configured on an "AP profile" level.Typically (and best practice), the SSH access to the APs is not enabled:AP Profile Name : default-ap-profile... Device Management : Tel...
Resolved! Access Point Real - Time
Hello everybody,I am just confirming whether or not Access Point Real - Time Statistics is available on Amsterdam 17.3.4c. It appears that it is available from Bengaluru 17.5.1 and up but I am not sure. Thank you for the assistance.
Resolved! 9800 log filtering
Hello, I was just wondering is there a way to filter certain messages so that they never even appear in the WLCs syslog? For example I would like to filter "%SESSION_MGR-5-FAIL" messages, or messages that contain certain strings, for example "Authori...
Hello Experts, I am facing a issue with guest access authentication. Old AIROS wlcs are working but now I have a installed a new 9800 wlc and its creating an issue. Requesting help to troubleshoot below authentication fail error messages seen for wir...
