Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello!Every One hopes You will be fine!we have facing an issue with WLC Username showing unknown.i also enable WLAN's > WLAN >Advance > HTTP check box but issue is still facingx
Hi everyone,How are you? I was wondering if it is possible to build a Layer2 Tunnel between IR829-1 and IR829-2 using Cellular. And if it is, would anyone be able to assist me in doing so?Thank you very much
Gudday allI have been in my work here now for 8 months. In that time there has being a consistent problem with Androids, iPhones, iPads, but strangely not laptops, not getting wireless access.At times it seemed that none of these devices could access...
Is there any way to get a list of the country codes configured on access points either from the controller or via Prime Infrastructure?I have a controller where we are nearly at the 20 country code limit and I want to check which codes are actually b...
I'm upgrading my companies wireless system. Going from a 2504 WLC to a Catalyst 9800 WLC with 2802i APs. As far as I can see (on my Cisco Smart Licensing account) the WLC and the AP are registered and licensed. The AP can associate with the controlle...
Resolved! Best Practices dual 5Ghz Aironet 2802i
I am looking for best practices for running 2802I access points. Running in a Dual 5Ghz radio configuration. We have trasnitioned to 5Ghz only devices so we have turned off 2.4Ghz. The reason I am asking the question is that all of my ap's have dua...
Resolved! Updating Meraki guest SSID
Has anyone ever created a script to update the guest SSID MX 68? I have about 200 deployed right now and am looking to change the guest password for all the units simultaneously.
Resolved! WLC 5508 Dynamic VLAN
I have set up an SSID with 3 dynamic VLANs that are issued with Microsoft NPS. The interfaces used are currently tied to other static SSIDs on system and work correctly. When a client authenticates they are put in the correct VLAN and are assigned...
Hello everyone!Has anyone used the IW6300 and encountered the following bug?In Flex mode, I have the SSID "alpha" mapped to VLAN 611, and in the internal switch of the IW6300 on port 2, I have the access VLAN 611 defined.The first thing that one assu...
I have several IoT temperature sensors:https://www.controlbyweb.com/xw110/ I recently upgraded my whole building wireless from Ubiquiti products to a network of 13 Cisco Business 240AC APs. The IoT devices seem to connect for a few minutes and then d...
I am converting ap 9115 to EWC.Issue1.After I set the ip address and gateway on the interface Gi for EWC.I enter 'write' command to save the configuration.But the error log is displayed on the screen "Failed to save vrrp-ip.txt".I have also set the s...
Hello,My apologies, but this was the closest community that fit my issue.We are using the Cisco AnyConnect Secure Mobility Client Version 4.10.01075 and we use RSA hard tokens and soft tokens for users to connect to our network via VPN. For some reas...
Hi all,We currently have a case open with Meraki going on 6 days now. At multiple sites we've been seeing sporadic issues with our clients passing traffic through access points. When we look at the AP in question we are seeing high latency from it (1...
Hi,Does cisco ap supports 8:8x8 radios, What does it mean by 8:8x8Do we really need 8:8x8?Any switch that give class 6 Poe for the wifi6? Thanks
Resolved! 9800 Controller netflow exporter
Hi we have an 9800 Controller and we are using SDA Wireless, we have setup our DNA center server as our netflow exporter. I would like to know if we can export our flows to more than one flow export server in the same SSID. Example: SSID Corp - Expor...
