Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! DHCP proxy mode - confused!
Hello, I am working with an environment that is a bit all over the shop, when it comes to the DHCP configuration on several of the WLC interfaces. There are several SSIDs, each linked to its own interface on the controller. In the switching environme...
I am using the 702w AP on a controller running 8.0.133.0 code and using the 4 LAN ports on the AP. For the LAN ports - I want to be able to see a port and see what MAC address is learned on that port. Would also like to see basic stats to look for e...
Hi wireless pros,it's me again with a Cat9800 question.In release 17.3, the following feature was introduced:===================================================Client Roaming Across Policy ProfileThe controller allows seamless roaming between same WL...
hi everybody i have tested wired guest lan with one C9800 Foreign in the LAN and one C9800 Anchor in the DMZ.it works very well with this.but with this architecture "foreign/anchor", i must have 2 C9800 and use a DMZ. it's possible to use a guest wir...
Resolved! AIR-AP3802I-B-K9 Power Requirements
Hi, just connected a AIR-AP3802I-B-K9 AP to the network. The AP seems to be stuck in a boot cycle. In this doc you can see that the AP requires uPOE. Is this my issue? Thank you I will be able to ping the AP for a short period...then, it goes do...
Hi wireless experts,I'm a "last follower" in Wireless technologies and in the process to evaluate the C9800. If you look in the very details, the thing is very differently from the AireOS boxes... Now I'm struggeling regarding the right IPv4 ARP / IP...
We have WLC and layer 3 switch and a lot APs which are connected to the switch with vlan20 access port. The users can get ip address from dhcp pool (10.0.20.0/24) located at the switch after connecting to these APs. Now we have the second dhcp pool(1...
Hello all,we have purchased new 9100 series APs and we are planning to use them with the existing controller 5520. As I know that these catalyst APs are supported with 5520 on a specific version.so my question is if I have a sufficient AP license on ...
Resolved! Why AP with Flexconn mode flashing
Hi AP with Flexconn mode means the AP is still able to work after disconnection with wlc. But why I see its light is flashing after disconnecting to wlc? Is this normal? Thanks
Hello. I want to run the 9100 AP with the 5520 WLC. Do I need a license for this? Or is WLC's own RTU license enough for that? """" Cisco Catalyst 9100 Access Points can connect to both AireOS 3504, 5520, and 8540 controllers and Cisco Catalyst 9800...
Hello all, I would like to implement QoS on Wireless on my SDA Fabric, 5520 WLC's are used.I created an application policy on the DNA Center for Wireless and deployed it on my test SSID. It created a FlexConnect AVC Profile, but here's the thing, my ...
Hi! I got newbie question and I`m not sure if it´s imbossible to do. But situation is this as described below. I´m doing this outside broadcast AoIP based system, which includes few switches and mobile router. I have Cisco SG350-28P switch and it´s r...
Hi all,Is that required to reboot the controller after we configure SNMP V3 ..? Any related document reffering this ...?KVS
I am seeing in my AP logs and the controller SNMP logs that my 5Ghz channel is changing a lot the past few weeks. (with rising complaints of disconnects) This is occurring on what seems to be almost every AP on this small campus of 6 buildings, usi...
Does anyone help calculate the live coverage of wifi meraki model mr56. please help me
