Hi all.I have deploy some of Catalyst C9130AXI-F AP with monitor mode to monitor channel interference and stuff. Is there any way to view / export the result of that monitor mode?Thank you. Best regards,Lazuardi Nurfaiz
Forum Posts
Hi, I have the wrong image and cant reset it, also when i type i get weird letters Please tell what need to do? below is the what have on CLIi have the wrong image and cant reset it, alsoAP003a.7d09.17d8>dnIOS Bootloader - Starting system.flash is wr...
Resolved! Mesh Trunking
I recently inherited a campus-wide mesh network of 6 RAPs and 14 MAPs. We have 4 remote switches bridged through MAPs. As-is, the network is working, but there are some things that we would like to clean up and future-proof on the LAN.In their curren...
Resolved! Open and Enhanced Open on same WLAN
Is it possible to have both Open and Enhanced open (OWE) on the same WLAN?Like how you can enable WPA2 and WPA3 on a WLAN, I would like to enable OWE and still support older clients that don't support WPA3 OWE.Thanks!
My c9800-40 pair always shows and Red(Amber) Alarm led on the active unit. At first I thought it was the stand-by unit but no it be the active unit and toggles between boxes if I trip failover.There is no such behavior documented . Documentation wo...
Hi Team, Could you help me with this?I want to configure more than one AP like RAP on the same MESH, should there be any consideration in the configuration of that MESH, the RAPs or the MAPs that I need to know?I mean if there is a priority or somet...
HiIs it possible to connect AP to PC directly by USB-RJ45? The AP has external power connection. Thank you
Resolved! Cannot change AP into FlexConnect mode
Hi AP 3602 cannot be changed into FlexConnect mode with vWLC. I got error message when I do that even if I change controller name. Please see below message attached. Thank you.
Greetings fellows, Kindly assist about the configuration to add Cisco AIR-AP1832i-K9 to a Cisco WS-C3650-48PS.I have been trying to google the concept and configuration steps but I have found a clearly document step by step configuration that I can f...
I know these are old AP's, but they were still working when I pulled them out of service. I am trying to find the Autonomous firmware for Air-Lap1242ag-a-k9. Someone must have a version somewhere and I am desperate to find it please. Thank you for ...
Hey all,I got a central WLC 5008 and a lot of 1142 Access Points.One of them doesn't boot anymore. I don't know what happened.When I console to it, it says:The system was interrupted or it encountered an error during initializion of the flash file sy...
Client can not connect to 2802 AP while roaming from 2702. I see the following msgs in AP logs. As soon as client is in 2702 radius then it connects again. Let me know if you need more info. Any help is appreciated.Feb 26 12:26:46 kernel: [*02/26/201...
Hello Team,we are doing office extended setup on cisco 5508 controller with 8.5.135 airos and 2702i access pointcontroller is behind firewallour 5508 controller is not dedicated for the OEAP setup our controller working as gust anchor controller also...
Can anyone tell me if there's any magic needed to get the standalone Aironet 1602i (AIR-SAP-1602I-E-K9) to react on its web interface? The device comes up when connected to the switch (Netgear M4100-26G-PoE), blinking green status LED, then I guess ...
I am trying to configure a new Aironet 1240AG. After it picked an ip address from the DHCP in my lan, I still can't log in using the web interface. I am using an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find server. please i need...
