Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello all.I currently have a single 5520 WLC running 8.8.100.0. It's being asked to run APs in the -B and -E regulatory domains however my reading tells me that mesh APs will face some challenges if the WLC is set to support multiple countries. We cu...
Hi to All, Can any one tell me why AIR-AP2802i-A-K9 cannot achieve POE full power went connected to Cisco switch WS-C2960S-48FPS-L with software version 15.0(2a)SE9. WS-C2960S-48FPS-L power inline was already set to static 30 watt. But when we try t...
Hi All,Our office is on top two floors of the building and straight on the roof there are many different Telco (Including Telstra and Optus) 3G, 4G and I think recently 5G equipment installed (Can’t verify).I have Cisco Virtual Wireless Controller wi...
Resolved! password for wireless network
Hello for everybody. Is it possible to find unencrypted password from config for [WPA2][Auth(PSK)] password. A wifi network was found on one of the controllers 3504, but password for it couldn't be found. It is dangerous to reset it, because there ar...
Resolved! C9800 HA to a in production C9800
Currently we have C9800-40 running 17.2.1a in production and working. We just received the HA controller and I need to get them setup as an HA pair. It appears that forming the pair will wipe out my current configuration on the production controlle...
Setting up and adding a Air AP3802I-B-K9 into a Cisco Meraki network thru a Meraki MS125-48LP switch
Anybody please...we were given two Aironet AP3802I for our newly renovated 4th floor. I connected these APs into our MS125 switch on the 4th floor which is connected to a MS320 core switch on the 1st floor. Is the AP3802I with a built-in mobility ex...
The Field Notice FN70489 is affecting an IW3702 that I got for setting up a test lab. I can use CLI and make changes in the parameters and get it working but I need the GUI interface for verification purposes. With this issue, I can browse into the m...
Hello there,I am a Network Administrator. I have one question today. I have tried to read about regulatory domains and their effect on the wireless network. But, I couldn't identify the exact effect of the regulatory domain of devices that produce in...
Resolved! WLC SSO on LAG Standby goes offline
Hi Guys WLC 5520 x 2on SSO Configured and it's working I'm using LAG on both the WLC's the stand-by WLC port sometimes goes offline due to which the failover doesn't take place during this time. as per the documentation from cisco we cannot set LAG a...
CISCO IR1101-K9's Cellular Interface doesn't have an option for the SLIP encapsulation. Current image is ir1101-universalk9.17.01.01.SPA.bin. Kindly asking anyone for a solution on what way to enable the encapsulation slip? Appreciate your help in ad...
Hi All I am trying to deploy an AP in the field for a rapid deployment scenario on a mine site.All of our existing fleet of 1572 APs are powered by DC and access the WLC via a PtMP backhaul system and set up as RAPs. They connect directly to the back...
Hi,Recently I tried setting up a test SSID with 802.1x using local net user and PEAP, but had problems with a client on a Samsung Galaxy s10+ trying to connect to the SSID. They are able to connect to the PSK based SSID, just not the 802.1x based one...
Hi,I’m using a AIR-CAP3502I-A-K9 access point.Getting over 300 mbs on wired (ethernet) computers, but any device (phone or laptop) on wifi will get less than 100 mbs.Is there any way to speed up service on wifi devices?
Resolved! IW3700 2x2 MIMO
Is there a way to specifically assign the IW3700's antenna ports to either 2.4GHz or 5Ghz only or 2 Ports for 2.4Ghz and 2 Ports for 5Ghz for a 2x2 MIMO configuration? Would this be done through CLI or the GUI?
Hi everyone,This is my first post here so if I'm not posting on the right area maybe an admin move this to correct area. Also keep that in mind that english is not my native language so I might sound strange sometime. I was trying for the past couple...
