Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
We have a Cisco WLC 4402 running version 7.0.253.3. Does that version support the ability to setup OfficeExtend. Hopefully this would allow me to setup an AP at my home that would always be connected to my internal network here at work. I can do the ...
At present, I encountered a problem, some AP1600 showed abnormal symptoms. They can register to the WLC normally, but after a few hours of operation, they will disconnect from the WLC and cannot register again. I extracted some key information:Msglog...
Hi, we are using a WLC 2504 (Firmware 8.5.161) with five AP2702i access points and have come across a strange issue.When I add a new interface to the controller with IP address 192.168.210.250 the controller freezes. Further access is only possible v...
Hi I have some Access Points that have left holes in the coverage, this is mainly on the 2.4 ghz if i change manually change the power levels on these will it affect the power levels of other Access Points that have their power set Globally and cause...
Hi forum, Last week I purchased a WAP571 access point. Radio 2 (2.4GHz) works exceptionally well. However, Radio 1 (5GHz) has a VERY poor signal. To properly test this, I have reset the AP to defaults and disabled Radio 2, and I can only connect ...
Resolved! Mesh Wireless Verification Help
We have two AIR-AP1562I-B-K9 APs forming a wireless bridge between two offices. This functioned normally until today. Is there any command that we can run at the Root AP to confirm whether or not it's seeing CAPWAP discovery traffic from the Mesh AP?...
Could someone please concisely explain to me the difference between the standard Bridge Mode on an AP and Workgroup Bridge Mode? Thanks in advance,Andy
It is the possible jump from 8.5.140.0 to 8.10.112.0
Hi, I am trying to see RFID updates on DNA spaces using WLC 3504. I am able to see all the updates of associated and unassociated clients on DNA spaces but not able to see RFID tags which are transmitting CCX_V1 messages.I can see RFID tag updates on...
Is possible to implement two factor authentication over a WLAN or with switches network with Ciso ISE. I have implemented this for VPN with Cisco ASA and RSA but I not sure if it is possible with switches and WLCs. Note: I've already read about eap c...
I have C9800 wireless controller, i want to configure MAB authentication, using local database of wireless controller. when i add mac address of the device on the controller and try to connect, the controller denies the connection, can you help me th...
Resolved! HA in Anchor controller Secnario
Hello Experts, could you please help me to understand better insight of HA within Anchor Scenario. i have 4 internal WLC 8540 controllers and 2 wlc's in DMZ. Internal 4 controllers are working in HA that means i have 2 pair of HA in my Internal LAN ...
HiI'm planning on bringing all WLCs up to the same code now we have got rid of old 1240 & 1140s.Issue have found is taking me 17 minutes to update 1 AP, from reading up on this, this is down to the code upgrading from and upgrading to, has to reboot ...
I successfully installed iPSK Manager and everything appeared to work however I am unable to log into the portal to create endpoint devices. I can enter the management portal using only the pre-built “administrator” account. I have tried using inte...
Hi, I have a 3702i repeater configured autonomous and I am able to connect to it, but it seems that using a laptop or phone does not get out to the internet. From the repeater I can connect to the internet. If I set up the dot1 radio as a workgroup b...
