Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
After upgrading my 9800-CL to 17.3.3 PIV auth via GUI doesn't work. I can log in via CLI using the PIV card. This is my config ip http secure-serverip http secure-trustpoint HTTPip http secure-peer-verify-trustpoint HTTPip http secure-piv-based-auth ...
I am currently setting up home lad for the purpose of my CCNP ENCOR exam. Been trying to deploy vWLC in Hyper V with the following IOS images 8.3.150.08.2.170.0 When booting to the IOS image, i keep getting the following issues : - Running at the ...
Resolved! 1810W Security Screw
Morning folks. We have some 1810Ws on loan from Cisco along with the additional mounting kits which come with a Torx Security Screw. The screw is described as being an M2x5.5 Torx - pictured below (the increments you can see on the ruler are in mm)....
I am working on a Centralized design model wifi VIRL lab for 5k end-users using CAT 98xx for Campus wireless edge for over 5000 users connecting to AWS? I have a core pair of NX 7707 with SUP 2E running OSPF?Will VOIP traffic be affected on edge? D...
Dear All I have question about channel width 80+80 on cisco WLC is different 160 I see channel width 80+80 have both wifi 5,6 but i not understand why use 80+80thank you
Hi everyone I would to kindly ask what is Difference Between IW3700 Series IOS Wireless LAN Recovery vs IW3700 Series Controller Based SW Image ? since I want to quote AP IW3702 on CCW but I don't know the difference between those software option? P...
Hello,I have two Cisco 3802i-E Access Points were I need a higher power level on the 2.4 GHz WiFi that I will get a stronger singal, because I want to build a Mesh between them because I am not able to setup a cable on the other site.According to the...
Hi there "standalone access point mode" -> Which means that there is NOT special / proprietary Hardware (Rack device) or Software from Cisco necessary... so i can use it just as an "normal" access point (as a bride) in EVERY (Cisco-independent) netwo...
Can anybody help? Since Android 11 was released I can no longer connect some users to a SSID using Meraki Authentication. The firmware update from Android essentially removes the users capability of choosing to trust a certificate. This is apparently...
Hi. Printer Issues Wifi, Wireless Network Management We have two RICOH printers here at work and all computers connected to the Ethernet on our network can print just fine (we have CISCO Switches). When people use the wifi, however, they can't see ...
Hello,vWLC is setting at ESXi and it has a management interface 10.0.10.2/24-vlan10 and a dynamic interface 10.0.20.2/24-vlan20. The ESXi host trunk to a physical switch that has vlan10 with ip address 10.0.10.10/24 and vlan 20 with ip address 10.0.2...
Resolved! Wireless Bridge between 2 buildings
Hello everybody,we need to connect 2 buildings - 2 networks with a wifi bridge at gigabit speed.The network uses vlan trunks, distance about 30 meters.Can you suggest units?Thank you,
Resolved! 9800WLCs copy config from lab
Hello there We are trying to migrate WLCs 9800s ACS TACACS+ to Cisco ISE. We were successful in migrating in the lab, but we have issues while on the actual production, is there a method to copy the lab configurations to the actual production. in s...
Resolved! Wlan error
Hi all trying to access wlans but getting the attached error all flex-connect is turned off but still can't access it
1852 restart repeatedly,After upgrading the firmware under u-boot, I can enter the prompt and show version, but restart immediately。What should I do?Can I use part2 to boot? ——————————————————————————————————————————————(RNAQ-C7) # bootipq tftpSpeci...
