HiAnyone here that got experience with configuring wirless guest authentication with fortiwlc(Meru) and Cisco ISE ?If someone have some information or can give me a clue how to proceed with this it would be much appreciated
Forum Posts
I have been tasked with exploring other wireless vendors and have spoken with Meru regarding their unique approach to a single channel environment. Does anyone have any experience, insites, good/bad info regarding Meru?I have this so far:http://www.u...
I did an upgrade of CPI from 3.8 to 3.9 today. I did a backup of the 3.8 setup and restored it to the new 3.9 VM setup. It now seems that after the upgrade, all APs (we have around 3000 in the network), have 'lost' their map location. They all come u...
HI Site survey can provide interference info, and WLC(new version) also can does it. Sometimes I notice the interference almost does not exist when we check Interference in WLC(new version), however it shows strong CCI/ACI if we do side survey for th...
Resolved! macos wifi rssi debug
i have a macbookpro os 11.2.3.i connect wifi display rssi is very poor,but i see wlc client status is okwhat wrong with the apple? its very suprise
![YOIPU8S%$UZWGL1HC}[U]24.png](/t5/image/serverpage/image-id/106338iD7C0B07F9872DE96/image-size/medium?v=v2&px=400)
Hi, I have a 9800-CL Wireless Controller running with Flex connect mode, i have a question on how can i apply the function like previous Air OS Cisco wireless controller "interface group" to 9800-CL Flex connect mode? Thanks
So if I set channels to 80 or 160 I cant seem to break the 600-700Mbit upload/download with the 9130ax aps, yes I'm using AX enabled devices that when tested on a router from netgear I get 900+ in most cases Also, how do I make it use 80+80 bypassing...
Resolved! Question about Roaming
Hello All, I have some question regarding roaming which confuses me. -Is the Roaming decision is decided by the client ? or the WLC ? what the threshold value on the client roaming section in the wireless tab refers to? -I was performing some debugs ...
Hi,Im trying to give static IP address to meraki AP however its not taking it If i check in switch DHCP IP os mapping to MEraki AP MAC addressPlease help
Hi We have WLC 5520 and AP 3800. One concept is not very clear. The below screenshot shows the two interferences expression at the same WLC. The first AP interference in the top picture is about 83% and the first AP interferences in the bottom pictur...
Hi I've a problem. I've two vWLCs running active-active so AP redundancy is in use (High Availability setup). APs are joining to Primary but if I try to move an AP to Secondary but it's not joining.Time - clocks are in Sync ( 3-4 sec deviation) and N...
Resolved! Channel number cannot be changed
Hi Why channel number cannot be changed for 2.4GHz? Under RF Channel Assignment of 5 GHz, channel number can be changed. Under RF Channel Assignment of 2.4 GHz, why channel number cannot be changed, it is grayed out. Please see the below picture. Tha...
Resolved! iOS IP Conflicts
I have multiple sites sending alerts for IP conflicts recently. It is only iPhones, and only on our wireless. I have SSIDs and a VLAN setup dedicated just to mobile phones, and the MX running as DHCP server for that VLAN. This was not an issue until ...
Hello, I have a catalyst 9800 WLC showing repeated CAPWAP-IDB Error lines in "show logging" output (pasted a sample below).Any chance someone knows what this is about ? I tried googling the full error text (without timestamps) as well as different pa...
Hi, I'm trying to setup a study lab, using two AP3600. They have latest firmware. I'm just struggling to understand the behaviour and get this right, so I'm hoping someone who has successfully done this before can help. I have one AP3600 as Root AP, ...
