Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I know these are old AP's, but they were still working when I pulled them out of service. I am trying to find the Autonomous firmware for Air-Lap1242ag-a-k9. Someone must have a version somewhere and I am desperate to find it please. Thank you for ...
Hey all,I got a central WLC 5008 and a lot of 1142 Access Points.One of them doesn't boot anymore. I don't know what happened.When I console to it, it says:The system was interrupted or it encountered an error during initializion of the flash file sy...
Client can not connect to 2802 AP while roaming from 2702. I see the following msgs in AP logs. As soon as client is in 2702 radius then it connects again. Let me know if you need more info. Any help is appreciated.Feb 26 12:26:46 kernel: [*02/26/201...
Hello Team,we are doing office extended setup on cisco 5508 controller with 8.5.135 airos and 2702i access pointcontroller is behind firewallour 5508 controller is not dedicated for the OEAP setup our controller working as gust anchor controller also...
Can anyone tell me if there's any magic needed to get the standalone Aironet 1602i (AIR-SAP-1602I-E-K9) to react on its web interface? The device comes up when connected to the switch (Netgear M4100-26G-PoE), blinking green status LED, then I guess ...
I am trying to configure a new Aironet 1240AG. After it picked an ip address from the DHCP in my lan, I still can't log in using the web interface. I am using an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find server. please i need...
Resolved! Can not access autonomous AP by GUI
Hello, Autonomous AP c1140 and PC can ping each other. Ip address 10.0.0.10/24 is added to BVI interface. http and http secure-server are enabled. But it cannot be accessed by GUI. Do not know why cannot access Any suggestions would be highly appreci...
Hello Experts, How good is the practice of converting a wireless access point in an autonomous mode for Wireless Site surveys?I have a huge site for site survey, and I am planning to convert the light weight APs(2700 & 1572) to autonomous mode. My m...
Our customer has several 1852 indoor APs powered by power injectors. Recently a few of them stopped working. Inspection shows that there were burnt marks on the boards near the AP's power supply circuit.We are wondering what could have happened. Can ...
Resolved! Help with AP 1850 software upgrade
Dear all, Could you pls help me to resolve the current situation: I've tried to upgrade the AIR-AP1852E-E-K9 (Mobility Express mode) from 8.3.112.0 to 8.10.130.0 and something went wrong.# I downloaded the software, installed TFTP server in my lapto...
Dear AllI did configuration follow config guide this link "https://www.cisco.com/c/en/us/td/docs/wireless/controller/ewc/17-2/config-guide/ewc_cg_17_2/secure_ldap_.html" but i don't see log request or receive from WLC to LDAP =======================...
HiDoes anyone know what numbers the cables are on the antenna RE: AIR-ANT2524VAC-R? I know the Cisco 3802e is numbered 1-4 clockwise and I'm aware the ANT2566 is numbered/lettered ACDB = 1,2,3,4, like below for example. Thanks in advance.S
Hi.I'm doing a lab, I have a 2802i AP as the mobility express controller, and I want to associate a 2602i to it, but I'm getting this error in the console of the 2602i: *May 21 20:30:15.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip...
Hi all,After adding a 9800-CL to Prime I got a critical alarm. Does somebody know the reason for this?Catalyst 9800 Telemetry coral connection failure for device IP 10.1.51.11. Please check the coral connection.Many Thanks!Regards, Urs
Hello, Although configuring the C9800 from CLI, even RMI SSO, when I'm connecting via HTTPS to the controller, the following is displayed: "This device is detected as a factory-fresh device. To begin, Click on below cards to create a new user account...
