Hello Team,we are doing office extended setup on cisco 5508 controller with 8.5.135 airos and 2702i access pointcontroller is behind firewallour 5508 controller is not dedicated for the OEAP setup our controller working as gust anchor controller also...
Forum Posts
Can anyone tell me if there's any magic needed to get the standalone Aironet 1602i (AIR-SAP-1602I-E-K9) to react on its web interface? The device comes up when connected to the switch (Netgear M4100-26G-PoE), blinking green status LED, then I guess ...
I am trying to configure a new Aironet 1240AG. After it picked an ip address from the DHCP in my lan, I still can't log in using the web interface. I am using an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find server. please i need...
Resolved! Can not access autonomous AP by GUI
Hello, Autonomous AP c1140 and PC can ping each other. Ip address 10.0.0.10/24 is added to BVI interface. http and http secure-server are enabled. But it cannot be accessed by GUI. Do not know why cannot access Any suggestions would be highly appreci...
Hello Experts, How good is the practice of converting a wireless access point in an autonomous mode for Wireless Site surveys?I have a huge site for site survey, and I am planning to convert the light weight APs(2700 & 1572) to autonomous mode. My ma...
Our customer has several 1852 indoor APs powered by power injectors. Recently a few of them stopped working. Inspection shows that there were burnt marks on the boards near the AP's power supply circuit.We are wondering what could have happened. Can ...
Resolved! Help with AP 1850 software upgrade
Dear all, Could you pls help me to resolve the current situation: I've tried to upgrade the AIR-AP1852E-E-K9 (Mobility Express mode) from 8.3.112.0 to 8.10.130.0 and something went wrong.# I downloaded the software, installed TFTP server in my lapto...
Dear AllI did configuration follow config guide this link "https://www.cisco.com/c/en/us/td/docs/wireless/controller/ewc/17-2/config-guide/ewc_cg_17_2/secure_ldap_.html" but i don't see log request or receive from WLC to LDAP =======================...
Hi.I'm doing a lab, I have a 2802i AP as the mobility express controller, and I want to associate a 2602i to it, but I'm getting this error in the console of the 2602i: *May 21 20:30:15.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip...
Hi all,After adding a 9800-CL to Prime I got a critical alarm. Does somebody know the reason for this?Catalyst 9800 Telemetry coral connection failure for device IP 10.1.51.11. Please check the coral connection.Many Thanks!Regards, Urs
Hello, Although configuring the C9800 from CLI, even RMI SSO, when I'm connecting via HTTPS to the controller, the following is displayed: "This device is detected as a factory-fresh device. To begin, Click on below cards to create a new user account...
Hello, we'd like to set-up workgroup bridge feature on new Catalyst 9800 WLC with transparency for VLAN-ID's (trunk via WGB) like on following link: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/service-set-identifier-ssid/211293-Conf...
Hello, I'm trying to connect 2 Cisco C9800-80 together for HA using Release 17.1. I was wondering If I was able to do the following. My two WLC's are in two different in DC's. I want to be able to use RP and RMI. The RP ports for each WLC would b...
Resolved! Mesh over Ethernet Configuration
Hello,I was currently handed the following equipment and asked to make a wireless bridge to a permanently docked ship.1 x MX642 x MR702 x MR361 x MS120 - 8 FP1 x PoE InjectorThe thought process is that we would set up the MX64 on land and connect it ...
Hello, Our Cisco Prime doesn't want to load it's webpage today, has anyone experienced this before? I will be de-commissioning it at some point as we have another Prime server, but I need to get the floor plans off it. I can SSH to it though, so I'm...
