Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! WLC5520 HA CICM Issue
Hi,Built the 5520 in HA, already to go in to production. I need to add the CICM so followed the instructions https://www.cisco.com/c/en/us/support/docs/wireless/5520-wireless-controller/212170-Console-access-to-5520-8540-WLC-via-CIMC.html I had to re...
Hi Please see the below, which is from output of command netsh wlan show interface in PC:My question is what decide the speed. In this case, Receive/Transmit Rate are 65 Mbps. It looks like distance and signal strength do not impact the rate. Anyone ...
Hi, good day, How do you configure TACACS on an HA pair? Do you add both redundancy IP's to TACACS? What about the VIP (management IP), do you need to add this to ISE as well? In other words, from ISE perspective to have SSH access to CLI, do you add...
Hello Together, i have got an AIR-AP2802e on my table, which has the following issue. When the AP is powered on it, immediatly stops even before u-boot, asking for board-selections from 1-5 (1= 3k, 2=2k new, 3=2k proto, 4= Milos, 5=3KH) you have no ...
Hello Team, Tried accessing the cisco ASA in GUI , getting the web page to provide the credentials but the page keeps on loading and not logging in. the acs is not a hardware and it a VM. Please let me kow what needs to be checked. +++++++++++++++++...
Hi, I am looking to replicate an existing point to point wireless connection we have spanning over the length of a cricket pitch. The current hardware is a pair of Cisco Aironet 1300 (AIR-BR1310G-E-K9) set in a root/non-root bridge mode which allow v...
I got jobs for replace AP1602E to 1815i, I would config same as last i did't found ACL setting in GUI or must config on CLI?. I'm never use WLC before(Controller configuration CLI mode). I try to swap CAPWAP (Look like SW,Router) mode becuase i only ...
Hi group, I hace a 1602i autonomous running latest IOS. Powered with power supply, connected directly to cisco switch on a Gig int. I can't have more than 100Mbps connection speed, if I force, port shutdown. Tried, different switch port, different ca...
We are happy to announce the new portal for Wireless Troubleshooting tools: https://developer.cisco.com/docs/wireless-troubleshooting-tools/ (Externally accessible) We are excited to become part of the Devnet community, and provide a wide range o...
Recently we ran a Nmap scan of our wireless network using a client connected via Wifi. The scan showed common ports over the dynamic interfaces (80,443, 22,) as open and reachable from the client. Further testing showed that we were able to connect...
I've just deployed a new solution and im experiencing issues with clients not roaming properly. Access points are installed really close to eachother. There is 6 access points loated around the premises. For example im in one room, i can see that i...
Will it damage 3502E or 3602E, with the radios turned up to max power, to operate without 1 or more antennas? I tried hunting this up in the FAQ, etc but didn't find anything specific to these models.
We were not able to do add a new user or edit existing one under Lobby Ambassador Guest Management. Nothing happened when we clicked on links/button. At the same time we saw these messages in logs:*emWeb: Oct 25 05:41:45.690: %EMWEB-3-FORM_SUBMIT_CSR...
I have an AIR 3600 that has been flashed with IOS for standalone mode. If I do a reset using the mode button will it revert back to lightweight mode (and thus need a controller?)Thanks.
