Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello, Our clients don't get the full speed when on WiFi. When we check on the WLC most get a Connection Speed of 400 Mbps and a score of 50-66%. When I go to go to wireless tab >> 802.11a/n/ac >> RRM >> DCA the Channel Width is set to 40Mhz. I rem...
I have always been plagued with Mobility Express issues. Usually my 1852e and 1852i's not ever booting into Mobility Express for some reason. For some reason now, my new 3802i's won't ever get "into" Mobility Express. And seem to just stay as CAPWAP...
Hi all, I have some questions relate to Meraki AP. How should we place the AP wall mount or ceiling? And what is the range coverage of the AP in x axis, y and z axis in meter? For example we use MR52.
I have a WLC 3504 v8.5.140 I want to intergrase to the prime 2.2 but it shows me "Cisco device without support" inReachability: marked in green Admin status: managed Last inventory collection: "unsupported cisco device" Why do you show me this messag...
I have a 1602i acces point with 3 vlans and a ssid per vlan.Is it possible to set channels for each ssid?
Resolved! Mobility Anchor Problems
Hi I've used mobility anchors to do SSID sharing with two other organisations before over a site-to-site VPN - relatively complicated compared to regular Guest mobility anchoring - but despite small problems it worked well, and I understand all the r...
Resolved! End of Life
Kindly confirm if Cisco has announced end of sale for Cisco access points 1700, 2700 and 3700 series.
Hey guys, We have two WLC controllers in our envrionment and on a few occasions the HA has had to kick in. Some genuine issues and other occasions down to power cuts and lost connection etc. The problem is, we never know it's happened and can't seem ...
I have two brand new Cisco Aironet 1562D devices. I am having trouble figuring out how to configure them. I have been able to console into the devices, but I don't see a way to configure them with IP address and such. Is there a default IP for these ...
Hi we have a lot AP1131 connected to WLC5508. Now we replaced one 1131 with AP3602 to hope to get band n in that area. After we replaced one AP1131, our PC can get band n and fast speed. However, it looks like some people cannot get band n when they...
Hi We cab get configuration by command "show run" via console connected to AP. Can we get the configuration via WLC? Thank you
Resolved! WLC5520 HA CICM Issue
Hi,Built the 5520 in HA, already to go in to production. I need to add the CICM so followed the instructions https://www.cisco.com/c/en/us/support/docs/wireless/5520-wireless-controller/212170-Console-access-to-5520-8540-WLC-via-CIMC.html I had to re...
Hi Please see the below, which is from output of command netsh wlan show interface in PC:My question is what decide the speed. In this case, Receive/Transmit Rate are 65 Mbps. It looks like distance and signal strength do not impact the rate. Anyone ...
Hi, good day, How do you configure TACACS on an HA pair? Do you add both redundancy IP's to TACACS? What about the VIP (management IP), do you need to add this to ISE as well? In other words, from ISE perspective to have SSH access to CLI, do you add...
Hello Together, i have got an AIR-AP2802e on my table, which has the following issue. When the AP is powered on it, immediatly stops even before u-boot, asking for board-selections from 1-5 (1= 3k, 2=2k new, 3=2k proto, 4= Milos, 5=3KH) you have no ...
