Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Does anyone know of a way to added the wireless config to a 7925G other than manual entry?
Resolved! What does NAC State do?
Hi, I am trying to figure out what the NAC State option under Advanced tab in a WLAN does if I sett it to ISE.What extra information is sent to the ISE? I have a usecase to do both dot1x and MAB on the same SSID. To be able to do that I have to set N...
Hello all, I have three routers. Two C887VA-W and one C886W-VA that actually having the same issue. Both are upgraded to autonomous AP successfully (...i think) with proper format and then installing the ap802-k9w7-tar.153...tar image and finally e...
Hello,At the company where we have Wi-Fi network environment with access points Cisco AP 1832i and all APs are managed by a WLC 7510 with software version 8.3.143.I have the following problem, if a notebook user is in one environment and connected to...
Oon the CMX side, what we have is an on-prem virtual appliance running version 10.x. Our existing MSE is an AIR-MSE-3355-K9:V01:KQ45LZH physical appliance running 8.0.140.9 with 600 CAS's and is a physical appliance.There are a couple of things we n...
Hello, We have an external captive portal with external Radius servers. The user authenticates in our portal and then we submit a POST request to the "switch_url" parameter contained in the captive portal redirect URL. In some vWLC it works ok but in...
Resolved! AIR-LOC2710-L-K9 Password Recovery
I just bought one of these in and it was in production and I have no way of getting a hold of the login information. Is there a way to wipe these to factory defaults? I have been looking everywhere with no such luck.
Resolved! WLC 2504 adding AP's
HI! We have a WLC 2504 (7.0.252.0) with 3 x CAP3501i and 4 x AP1231G. We need more 2 x AP's. Challenge: buy more AP's but "try" to still use the old AP1231G. The newer AP's dont support 7.0.252.0 and the AP1231G dont support 8.5. After some research,...
After a survey we placed 12 access points in our warehouse. 3802's with 4x AIR-ANT2535SDW-R dipole antenna's each. In the WLC (2504 wlc) antenna gain is set to 6x0,5dBi for each accesspoint. We are using 2.4ghz only, 5ghz has been disabled (but when ...
We have two 2602 APs listed on a WiSM, running 8.5.140, that show an Up Time of 75d and 8d. However, these two APs appear in that order as the last two APs on the WiSM. Also, the VLANs default every night to the native VLAN instead of retaining the...
I need to disable the network to make some changes to wireless networks. I get an error message that it is operational and cannot make chantes. I have some meshes enabled. Would the mesh come back if i connect to WLC and disable the network, make cha...
Hi, I want to design a WiFi system for an outdoor large area (10000000 sqm) which can take up to (5000000 people) in which the active users from my operator are around (400000 people) distributed homogeneous around the area. My question is how much a...
wlc 5508 running version 8.2.170.0 shows the below vulnerabilities, how can these be mitigated? SSL Certificate Signed Using Weak Hashing AlgorithmSSH Weak Algorithms SupportedSSH Server CBC Mode Ciphers EnabledSSH Weak MAC Algorithms EnabledSSL Ce...
Hello, Strange one here. Firstly I'm no expert on our WLC 5508 (2 in HA mode). We have a few interfaces under Controller > Interfaces I guess these are the VLANs for the SSIDs. Our main SSID is on VLAN 121 and all is ok. However if I ping the IP of...
Hello experts, Need your advice here. We noticed multiple users in different areas of the building observing random disconnects from the network. We reached out to Cisco TAC and they suggested the following. 1>Disable optimized roaming 2>Disa...
