Hello all,I have a four AP MR42 conected fine , but today i had a cut on SSID , when i researched after on event log for access point i detected this :Single device packet floodradio: 2, state: end, alarm_id: 20 « hide reasonreceived_packetand Auto R...
Forum Posts
Hi Guys, I need your help.I have a Controller AIR-CT5520-K9 Does not work with module GLC-LH-SMD=. Two side with same GLC-LH-SMD=.Only one port SFP used.Please troubleshoot this problem
I need The default administrative username and password for AP521.I try admin:admin cisco:cisco
Dear community, Our customer is migrating all the VMware infrastructure (version 5.1) to new ESXi hosts (version 6.7). This includes a vWLC version 8.5.151. Is there any documented procedure to move the vWLC from the current host to the new one? Or ...
I have configured virtual controller as per below configuration: A. InterfacesManagement Interface - 172.16.4.5,255.255.252.0/untagged vlanWlan-User - 172.16.168.2,255.255.254.0/Vlan 5 B. WLANTEST: with interface group- Wlan-User C. APs are running i...
I have a Wireles LAN controller and Light weight access points broadcasting 2 SSIDs (Students-wifi and staff-wifi)on 2 differenet vlans(on packet tracer). Now the problem is the two APs are broadcasting the SSIDs to my wireless clients and i am now g...
Resolved! AIR-AP1832I-S-K9 Mode Standalone
Hi everyone,I have a question, does the AIR-AP1832I-S-K9 support mode standalone?I saw " Standalone " in deployments Mode, but in the software I can't find to download autonomous mode ( Only Lightweight and Mobility Express ).Please explain for me. T...
Hi all! I have an Cisco AP, model AIR-CAP1602I-E-K9. I have it set up as an autonomous ap and it's all working fine. However, I'm only able to achieve 54 mbit/s. I believe something is wrong with my configuration?#show running-config Building configu...
I have 9800 wlc with 24 cisco AP they are already associate with wlc but issue is i forget username and password of connetef AP is there any possibilty to change password globaly in 9800 wlc for all connected AP or verify password through WLC or if p...
I have installed 2 new Cisco WAPs but I can't poll these WAPs vai SNMP/ICMP within Solarwinds. WAPs are managed by WLC. The only polling method which works is status only ICMP. All of the older Cisco AIR-LAP1142N-A-K9 and AIR-CAP3602I-A-K9 can be ...
Hello Everyone, I have a WLC 5508 runing 8.0Presently one SSID is assigned to all th APs registered with my WLC.I want a different SSID to 2 of APs. Can anyone tell me how to do this?
Resolved! 2802E with internal antenna, when external antenna is plugged in does it disable internal ?
Hey, I've seen minimal cost difference between the 2802e with or without internal antenna. For flexibility is it possible to disable internal when external antenna is plugged in, or perhaps it's automatic ?Regards
I am in desperate need for help because I picked up 2x brand new Cisco AIR-AP3802I-Z-K9 and I don't have a wireless controller to run them on so they are pretty much useless at the moment unless I can get Mobility Express from Cisco - but you need a ...
Hi all! I came across an Cisco AP, model AIR-CAP1602I-E-K9. I have it set up as an autonomous ap and it's all working fine. However, I'm only able to achieve 54 mbit/s. I believe something is wrong with my configuration?Any tips or ideas? See config ...
Resolved! Cisco DNA Software for Wireless - Meraki
I do not see Meraki wireless here:https://www.cisco.com/c/en/us/products/software/dna-subscription-wireless/index.html it says:The wireless infrastructure becomes the strongest first line of defense, with Encrypted Traffic Analytics (ETA) and Softwar...
