Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I'm using AirCheck WI-FI Tester and I've saved some results that I would like to download. Can you let me know what software I need to download to interface with this AIRCHECK Thanks
hello, i have configured my FMC v6 with acs 5.8 in Radius for management all configuration is fine and i can access on FMC by users created in ACS but after the configuration the admin local account of the FMC stay always fonctionaly i think th...
Resolved! 2802 Mobility Express Configuration
I have a LAN with 17 x 2802 AP's on Mobility Express. There are four SSID's configured and the client would like two of the SSID's hidden on specific AP's. I know how to do it globally on the Controller/Master AP with the command below: config wlan...
Hi we noticed there is a different mac. Air1552 is connected to a switch. In the switch, we can see the AP's mac address, which is like this: xxxx.xxxx.xxe0, but in WLC side(main page-----> Wireless) we can see its mac address is like this: xx:xx:xx:...
hi all, just provisioned 1552 to join on a WLC 2504 8.2.170. i don't see the mesh tab (see ap-1) after it got registered to WLC. the other AP (same 1552 platform and OS - ap-2) had the mesh tab and was able to change role to 'mesh' anything additiona...
Resolved! Guest Anchor Management Interface
I am following the Enterprise Mobility Design Guide (below) and I am not clear on the position of the management interface. Fig. 10.1 and 10.2 show one interface on the DMZ. Fig. 10.15 shows 2 interfaces, one on the dmz and one on the management v...
Hello at all, is it possible to tell a flexconnect ap if the client at a single ssid should get local switched or central switched and if central switched, which vlan it should use? All I got so far was either central switched with dynamic vlan assig...
Hello all, we have a customer who has several locations with a Mobility Express setup. At one location we have nothing but issues. We have fixed several issues but one remains. One access point functions as a static ME controller but the other APs ...
Is it possible to use same IP addresses for redundancy management IP address pair and the regular management IP address pair on WLCs?
Hello All, I am new to Wireless network . 2 AP's disconnected from vWLC suddenly. I am able to ping the AP from local LAN network which is mounted in our network and even through controller I am able to ping the AP's. Virtual wireless controller v...
Hi experts. I have AP's connecting to a centralised 5520 controller. The controller on the wired side access VLANs 900 and 110 for the relevant SSID's. Hence we have: vlan 900 = SSID A vlan 110 = SSID B Our switches network is configured as VTP t...
Hello, I have a project where i was asked for a wlc that support wireless intrusion prevention system (wips), WLC 3504 suits the project but i am not sure if it supports wips or not there is no thing in the datasheet even for the wlc 5520, not a wi...
I was trying to run a report for Busy AP in Cisco Prime Infrastructure . It keeps telling me no protocol selected but I cant see in the report page where to select protocol
Web authentication don't redirect when enter URL but i can enter IP address.It's OK.I use WLC4404 and WLC 5508 and i enable Web authentication function when i access with SSID its enable Web authen.I enter www.google.com in URL it's not redirect to C...
Hello, I want to get a wlc 3504 with HA and smart movable license, usually for normal license we get LIC-CT3504-1A with license adder but when i searched about smart license i found that i have to get C1FPAIRK9 instead. so does this mean that nor...
