Hi,
It look like L2 protocols like STP, CDP,.. is by default transported across bridge domain from one AC to other ACs.
How is to disable this behavior on bridge-domain or AC ?
Regards,
Hi,
I am using VPLS with manual provisioning. I am expecting there is L2 looping within the bridge domain. but i can not find the way to detect it.
In normal Catalyst or ME switch, i reply on "MAC address flapping" log to detect with VLAN is looping...
Dear All
I try to test to enable IPv6 route exchange with IPv4 Neighbor address by enable "address-family ipv6 unicast" under Neighbor IPv4. I am using XR 6.0.1. I found some problem that Next-Hop Address on eBGP route is incorret.
[IOS XE ] <-bgp...
Good day, I am wondering to ask one thing.
I am doing some maintenance ASR9K in Asia Region.
Mostly I troubleshooted a lot of issue after failure occured.
But my client want to know more fastly in critical situation before happened.(Liked reboote...
Hi there!
Has anybody worked in the license activation for A9K-4T16GE-SE line card?
I was trying to configure the four 10GE ports for this line card with A9K-4T16GE-AIP-SE license, but just worked two of them.
Are there another license to enable the ...
Hi ,
Im researching about NSF, I get the main idea, "if a RP switchover happens, the NSF-capable router that does the RP switchover, sends a message to the NSF- aware so the sessions of the peer dont go down, and the forwarding of the packets can con...
Hello.
I would like to inquire the following regarding the configuration snippet below:
Bundle-Ether 100 consists of two physical links.
interface Bundle-Ether100interface Bundle-Ether100.1 l2transport encapsulation dot1q 50
interface Bundle-Ether100...
After upgrading to 5.3.4, FPA included, interfaces SFP+0 - 3 stopped functioning. I noticed that fpga version was not right.
show hw-module fpd location 0/0$Fri Dec 30 22:04:22.315 UTC
===================================== ========================...
Hi,I have CISCO 2900 series router which i use it in our ISP setup. The router has more than 250 static NAT configured on and a about 70 routes. The problem is, every after a while a random NAT disappers from the router. In show run one NAT goes miss...
Hello!I want to monitor traffic that matches in class-maps via SNMP (CISCO-CLASS-BASED-QOS-MIB) on IOS XR, but i can't understand some counters.class-map and policy-map config:class-map match-all Default0.0 match dscp default end-class-map!class-map...
We are using our asr9k with a lot of dslams (access gear). Well that is all layer2. I can't figure out how to dump a whole mac address table with ios-xr like we could on 7600s. I realize they are routers, but I would think there is a way to pull m...
Hi All
Playing around with EBGP XOR ver 5.1.3 ....I got some below log messages ..Everything is fine as far as routing and traffic is concerned ..A friend told me its a bug ..i couldn't find anything on it ..Please share your thoughts
LC/0/1/CPU0:D...
Hi Everyone, one of my global SP customers is planning to augment its network with ASR 9K with V3 power supply modules. And hence the customer is looking for the information related to v3 power modules details (detailed description, connection guidel...
I facing issue in policing traffic over bundle-ether. I have created a policy may and class map into it to classify three different traffic sources. The problem I am observing is that though traffic is under utilized from the police rate configured b...
We have several 9010 chassis deployed and one of them is experiencing repeated PWR-6KW-AC-V3 power module over temperature conditions.
Since there is nothing special about this location (same cabinet & power supplies, similar environment, etc.) and t...
