Hey all, I just want to know what the difference between the DNAC subscription (L-DNAC-MGMT-ADD) and the DNA Virtual Appliance (DN-SW-APL) is? What are the use cases for each? Please, provide me with resources! Thanks
Forum Posts
Hey all, I just want to order Cisco DNA Center Virtual Appliance. Simply via CCW I ordered DN-SW-APL and I found that there are two options: DNA-SW-AMI and DNA-SW-OVA I need to know how to differentiate between the two and which one is the most suita...
Hello, how can I configure a port on an edge node in sda fabric which is from a "layer 2 only" pool using the API?In the GUI it's possible to choose data vlans which originates from "ip address pool" or from a "layer-2-only network". Using the API I ...
I have 3 nodes, and two nodes have faulty parts.Node 2 requires an SSD and Node 3 requires memory.I cannot seem to find information about how to go about replacing these parts and in which order.https://www.cisco.com/c/en/us/td/docs/cloud-systems-man...
Hi, everyone I understand that the WLC cannot be used without adding it to the dnac factory, the possible solution would be to install an independent wlc with its respective AP to provide wireless?If you do not have a WLC, can you install only the AP...
Hey,So I'm struggling a bit with finding the correct AP sometimes, when the name might be unavailable to me, but I have the wired ethernet mac address.In inventory I can search by mac, but thats the radio mac - what gives?I think its quite inconsiste...
We recently upgraded our infrastructure to dnac 2.3.3.7 and our switches to 17.9.3 to be in line with current suggested code. However when we updated we started running into an issue when provisioning devices through host onboarding. DNAC keeps re-ap...
I'm evaluating DNAC and have some basic questions w.r.t Reporting,1. Does DNAC support scheduling reports going back upto a year (365 days) for all reporting types under the reporting templates?.2. Once a report is generated for how long is the gener...
Hi,We are currently evaluating a Cisco AIR-AP1800S-E-K9, but this is failing to be claimed in Cisco DNA.AP Running Image : 2.2.1.3Primary Boot Image : 2.2.1.3Backup Boot Image : 8.8.259.0DHCP Option 43 configured to use: option 43 ascii "5A1N;B2;I"DN...
Hi,We're planning to turn on Cisco AI Analytics in the near future. As part of the preparation I'll need to plan the change for approval, and I'm wondering if enabling the options provisions any config changes on our Switches or WLC (Non SDA). ie, do...
Hi,I have a requirement to deploy 1 line of CLI to a small selection of devices spread across multiple (but not all) all sites.In Prime Infrastructure this would've been really simple, but I can't figure out the best way to do it in DNAC. Is PI I wou...
Hi DNAC community, When adding a 9800 WLC to DNAC, I can see that the APs also try to establish a HTTPS connection Port 443 to DNA Center. As far as I know, only iCAP using Port 32656 is documented and in use. What's the purpose of the port 443 commu...
How do I use the Cisco DNA Centre API to find the site / location for a specific AP?I have tried the following API end points, but they don't return the AP site / location:/dna/intent/api/v1/network-device?hostname=.../dna/intent/api/v1/wireless/acce...
When i change the orgination details on grafana dashbaord it is not responding please suggest the steps to retrive the dashbaord
Hi, I have a DNA Center where we have pushed Telemetry collection to all Cat9k switches, and we are seeing some data in the DNAC.But when I look the application visibility service in DNAC it seems like it is not enabled: In the CLI the service seems ...
