Hi guys,My customer's device has pushed many alarms as below:RP/0/RP0/CPU0:Jun 22 06:16:26.532 +07: logger[66718]: %OS-SYSLOG-4-LOG_WARNING : PAM: Unable to copy data to peer RP (IP: 172.0.31.1): RP/0/RP0/CPU0:Jun 22 06:46:50.033 +07: logger[68367]:...
Forum Posts
Hi Team, I have noticed a weird behaviour on my ASR920 routers trying to configure VPLS l2 vfi TWC manual vpn id x bridge-domain x ! interface GigabitEthernet0/0/10 description Test no ip address negotiation auto no keepalive service instance x ...
Dears,I have Cisco ISR 1161 with Cisco IOS XE Software, Version 17.06.05 and we have problem on Cellular interface 0/2/0 that goes down/down all the time. I need help please !Here is the running-config as an attachmentThank you !
Hello,I am studying for Cisco SP VPN certification and am a bit confused while going through the Ethernet OAM and CFM topics.CFM topic refers to the following terms without giving any explanation on what they are:- Relay function side- Wire sideI eve...
Hello!I have bought a few Cisco C9500 (C9500-24Y4C) that I want to be used as leafs in a VXLAN EVPN setup (Multi vendor, different spines) I'm trying to get the local VLANs in the C9500 to get encapsulated and sent across the tunnels to the nve peers...
Hello i have 901-903-ME 3800 and i want enable these two commands : xml agent tty netconf agent tty but i can't how i can enable the two commands in ASR 900 : xml agent tty netconf agent tty i try to put but i can't ASR901-KHETMINE(config...
Hi Experts, Is there a way in an EVPN Multihoming Active/Active Scenario to be apply QoS policies on the CE facing interfaces in such a way that QoS policing will be done in aggregate between the 2 PEs? I would want to limit the CE bundle to be able ...
Hi everybody,Please help me how to get SNMP OID to get serial number ASR901 and ASR920
We are in a situation to test the performance and error rate of Ethernet Leased circuit, we have Cisco ME Switches on both ends of the circuit and want to perform BERT Testing. Is there any command available on Cisco ME switches to perform BERT testi...
Hi, AllI am currently having issue with clearing configuration under IOS XR. There is no command like write erase or delete start-up configuration.I have read some documents for IOS XR, the CFS seems to be the place where the configuration store. So ...
Hi All, I am trying to use a 100G Copper DAC cable between a Nexus 9300 router and an ASR 9006 with a A9K-4x100GE card. The cable works fine between the two nexus switches in their QSFP 100G ports, but I cannot get it to link from the Nexus to the A9...
I have a few ASR-920-24SZ which I'm testing. All ports light up yellow. When plugging in a GLC-SX-MM or GLC-SX-MMD the it gets detected in the CLI. But I'm not getting any green uplink. (all SFPs and fiber cable is working tested in many other cisco ...
Does anyone know about wan-phy features on: A99-4HG-FLEX-TRASR 9900 400GE Combo Packet Transport Line Card - 5th GenerationI can not see any configuration guide relate to Controller WAN-PHY for this line card on Internet.
Hello, is supported LACP on Catalyst 8200 and 8300 routers? Customer wants to use them as CPEs with LACP on L2 interfaces (LAN). Warm regards,Josef
Hello, I have a client who installed an ASR Edge router and wants to give public IPs to his clients, the truth is that I have been researching but I cannot find the material on how to do this. I understand that I have to connect the ASR to an AS BGP ...
