Buy or Renew
Buy or Renew

MPLS

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Forum Posts

Start a conversation

MPLS VPN management tools

    Hi folks, I'm looking for a tool we can use to hold a database of routing table's vrf and comparison with then during the time.Thanks in advanced for your recomendations

mbonilla by • Community Member
  • 787 Views
  • 1 replies
  • 0 Helpful votes

VPLS Implementation - Need some inputs

Hi All,We are planning to roll out VPLS services in our network and I need advice from people who have deployed VPLS in their network.In the real scenario customers may also come over wireless last mile and terminate on our MetroE network. From Metro...

Resolved! Sham-Link Question: UP but no effect

Hi guys,i met a severe problem with my lab. the enviroment consists 4 routers, 2 pe (r2 & r3) and 2 ce (r1 & r4). 2 ce and 2 interfaces of pes belong to area 1 and suprerbackbone is area 0. the mpls vpn is established ,and espacially the sham link is...

yuening liao by • Community Member
  • 1376 Views
  • 3 replies
  • 0 Helpful votes

Unframed E1 over MPLS (TDM over IP)

Hi,I am trying to configure an unframed E1 and trasport it over MPLS. I have installed one PA-MC-STM1 module on a 7206 PE router and one on the 7604 PE router. The STM1 level is UP and also the E1 level is UP. I am using AU-4 mapping  on our SDH netw...

n.taka by • Community Member
  • 7472 Views
  • 11 replies
  • 0 Helpful votes

Can Enterprises act like SP, to provide isolation for each customer traffic? (Enterprises whose backbone network is MPLS VPN links from SP)

Now a day’s trend is to get mpls vpn links from service providers & get to off-shore offices or customers. In which customer is typically using MPLS from service providers as transport medium from VPN customers prospective...where in all MPLS feature...

Resolved! Which object in RSVP message carried the value configured by "tunnel mpls traffic-eng bandwidth" command?

Hi Experts,I configured a simple MPLS TE tunnel in my routers and configured it with "tunnel mpls traffic-eng bandwidth 777" command. The tunnel came up fine. I tried to capture the packets (using GNS capture) going out of tunnel head end interface b...

mtsb by • Level 5
  • 1933 Views
  • 2 replies
  • 0 Helpful votes

MPLS to IP QOS tagging and MPLS tagging

I am trying to figure out how to make sure that packets that are supposed to be applied to QoS policies are being tagging going from the MPLS network to IP ( ie the cloud to the CPE).  I would also appreciate any guidance on how to implement mpls in ...

lkadlik by • Level 4
  • 3095 Views
  • 6 replies
  • 0 Helpful votes

Resolved! OSPF in VRF with same area ID

Hello all,On an MPLS/VPN PE router, I have configured OSPF as the PE/CE routing protocol.I configured several OSPF processes (one for each VRF).But if I have several customers who are using the same OSPF area ID on the CE side, may I configure the sa...

Sam Preston by • Community Member
  • 35882 Views
  • 4 replies
  • 0 Helpful votes

MPLS training question

Hey guys,I took an MPLS course online and it pointed something out I really didn't get, or at least need clarification on.The person giving the course said that because of how the PE's interact with the P LSR's that is isn't necessary to run a routin...

Resolved! VPLS over Carrier Supporting Carrier MPLS VPN

Hi All,I would like to get a clarification from all whether the following topology and my thinking are correct. Currently I am not able to do reproduce in my lab due to lack of hardware so seeking advice here.I am providing Carrier Supporting Carrier...

Managed FW on PE

Hi,I am working on a project where we need to implement a FW on a PE Router as a Managed FW for our corporate users.The proposed design is as follows:1. On the FW Side:  a. The FW will be deployed in off-path mode where the customer VLAN will be assi...

Resolved! MPLS Config Help

This is driving me insane, it's not a difficult problem, I have a loopback in the VRF on both cores, configurations were copy and pasted to ensure they were identical, BGP peer's are up, redistribution is working fine, but I cannot ping between the l...

Resolved! Maximum LSP on Inter-AS vpnv4/ipv4

Hi LucThank you for your reply, in fact we are in the process of using Option B (ASBR-to-ASBR). We have all the configs in place just did not activate the neighbors pending confirmation. We are using Eng5; I would expect CAM/TFIB to be able to hold t...

Resolved! QOS for Serial Interface in IOS-XR

Hi,I am trying to configure QOS for a FR serial interface in IOS-XR.But I don't see an option for configuring input/output service-policy in IOS-XR 3.9.1  for serial interface. These options are available for ethernet subinterfaces..Following is the ...

kokulsharma by • Community Member
  • 1164 Views
  • 2 replies
  • 0 Helpful votes

6PE label allocation question

HelloCan someone with experience of 6PE please clarify a question for me?The following doc says that 6PE allocates aggregate labels for BGP prefixes from a pool of 16, which are used in a round robin fashionhttp://www.Cisco.com/en/US/products/sw/ioss...

Load more