What is the standard procedure with steps to do QOS testing for multiple type of traffic before and after?
Forum Posts
Our core switches are Cisco 9600. We have a few Cisco 9300 and old Avaya switches on our network. We have many buildings in different campuses. The network guy has superscopes for each campus. A few buildings have different VLANS. The IP helper on th...
Greetings, I'm trying to configure an EEM script with an 'event of none', so that I can manually run the EEM script. I basically have the following script configured on a router. event manager applet TSHOOT event none action 1.0 cli command "sh r...
Resolved! no auto summary BGP
Hi all I can't issue the following command. no auto summary command under router bgp 65000 conf trouter bgp 65000 no auto summaryit goes under address-family ipv4 will that be an issue? address-family ipv4no auto summary
Resolved! Change Config-Register
I had 700+ days of uptime on my DR router, so I rebooted my DR router last week Friday and it did not go well. Ended up coming up in a factory-default state, even though I know I've saved the config multiple times. Today I got a chance to dig into ...
Resolved! BGP sacn import address-family vpnv4
Hi alladdress-family vpnv4(config-router-af)#bgp scan import 10%NOTE: This command has been deprecated.Does anyone command for this I am using ISR router with IOS 17.X.X2nd question also I cannot see ospf subnets command in sh run or sh run all but t...
Hi I am looking for OPSF overload command to increase cost of OSPF for the whole Cisco router similar to OSPF overload command for juniper.
Hi all,I'm moving from OPNSense to Cisco XRv9000, and am trying to get internet access to the Cisco router. I can ping 8.8.8.8 but pinging www.google.com does not work.RP/0/RP0/CPU0:xrv1#ping 8.8.8.8 Thu Aug 31 13:32:21.410 UTC Type escape sequence ...
HI, I have a Cisco 2900 router currently functioning within my voice network. I am planning to upgrade to two new Cisco 4300 routers, replacing the existing Cisco 2900 router. To ensure redundancy in the voice network, I intend to implement HSRP (Hot...
I upgraded to the latest Prime software version 3.10.4 with latest Device pack, but for some reason Prime does not support a C3548P-10GX, I can configure and connect from to C3548P Prime fine, other switches like a 3548-X is supported under Inventory...
can I have N9K-C93360YC-FX2 designed usage ---> FEX aggregationport type port number 1/10 GE fiber ports = 9640 GE ports = 1225 GE port = 0100 GE ports ...
Resolved! ISR 4331 DHCP woes
I have an ISR 4331 with NIM-ES2-4 module in slot 0/2. I am attaching the output of show running-config.The 4331 WAN is 192.168.1.0/24, connected to g0/0/0 configured as nat outside, and this interface receives its IP configuration from 192.168.1.1 vi...
Resolved! 151AXM Mesh
Hi,I have a newly setup network of AP 150AX and Mesh 151AXM. The mesh AP's seem not to get connected even though the app says they are connected.The mesh AP's will flash blue for days. How do I troubleshoot these AP's?Thanks.
Hello Cisco Community,I hope this message finds you well. I am conducting a research study focused on the challenges and opportunities of enforcing network policies across various domains such as campuses, WANs, and data centers. As experts in the fi...
Resolved! ACL rules
Hello community Please I am kind of stuck with the following exercise. I completed it 3 times and still I have no clue about those mistakes in the 2nd and last questions from this sshot below with the right answers:-Staring with the 2nd,SRC 192.168.1...
