Hi all experts.I have written eem applet to send email when i particular sla object is up/down. Can i specify the source ip address when router sends this email ?I am using the following IOS c3845-advsecurityk9-mz.124-22.T2.binKindly guide me
LMS 3.2 Windows 2003 R2 8Gig RAMManaging ~4000 devices currently on LMS 3.1. Built new LMS3.2 server and patched to RME 4.3.1.Import from csv file works fine and RME inventory collection/ Campus Manager Data Collection all works perfectly.Archive Job...
Hello,I try to use the "cwcli config compareanddeploy"command in CLI since i need to make first report, then add several monitoring configuration lines in thousand of equipments.cwcli config comparewithbaselin -u *** -p ** -baseline templatesnmptrap...
We have just purchased a number of the 2960s model switches. I have one 'odd-ball' version of the switches out right now, it is WS-C2960S-48TS-S. It can't get it to sync the archive. No other device is having problems. The error states to check th...
Hi,Anybody have idea how to configure snmp v3 in 1800 series routers with Nagios configured for monitoring? Can we keep the community name if keep v3 running? I have configured snmp v3 as per the manual. But if I remove the v2 community name it stop ...
Hello,I'm trying to find SNMP OID (and MIB in which OID contain) to monitor L2 of ISDN PRI line.I've configured Nagios check for interface, but even serial 0/x/0:15 is up/up, that doesn't mean its working on L2.What I need is to distinguish between s...
We're currently using RME to upgrade Cat3750 IOS versions.At the end of the upgrade process the switch gets restarted via SNMP and then the job attempts and contact the switch whilst it reboots. After 5 attempts the job gives up and fails, however, a...
Hi,I need Compliance mgmt help.I want to run a command against 2500 switches that make all Fast Ethernet ports implement as speed auto & duplex auto, except Gig port and trunk ports. Any help appreciated.THANKSI am using;LMS:3.2RME: 4.3CM:5.2.1
Hi all,I have a problem access web interface CiscoWorks using the urlhttp://172.16.xy:1741 (on the server locally or remotely).but when I use http://lms:1741 or https://lms its work fine locally but not remotely.please help me to do it work remotely.
Hello friends,We have 50 Mbps for Internet access, and lately we have been experimenting congestion on the link, everyday from 10AM up to 12PM. We use cisco router 3825 for Internet access. After running NBAR we found a lot of peer-to-peer/file shari...
Hello!I haven't worked with Ciscoworks in a long time and see v4.0 is out. Does anyone if this app is a good tool to monitor bandwidth utilization? We need a good product that can monitor utilization on our WAN circuits and also doing regular backups...
I want to change the ip address on multiple devices configration.( the ip address will be different on each devices) is that possible to do on RME net config? i know I can do one command and valu on multiple devices but not sure if this possible. Tha...
Hello,I want to configure CiscoWorks Assistance I got error message "Error in communicating with DCR Server.DCR Server may be down. Please start the DCR Server and then refresh the page. ". I picked up CS-server-admin-Process, I found process "DCRSe...
Where can I find list of Cisco devices fully supported by CWLMS-4.0-SBE-K9, LMS 4.0 Small Biz Edition 50 Dev Restricted, WIN only?In some documents, I have found that it is restricted to access routers and fixed switching platforms only, but have not...
