I am running a TcL script on a Nexus 7k and would like to suppress the output from cli commands. The TcL book says it can be done by enteringt "log_user 0", which works on a ASR router but not the Nexus switch.Any suggestions would be appreciated.
Forum Posts
Hello Engineers!I would like to gather your opinions about having DHCP server versus switch DHCP POOL configuration.Currently our Cisco switch 3750X having some VLANs and each VLANs are providing IP addresses from the pool to clients.Sometimes I can ...
Hi all,i have my nagios system and i need the OID to set up the snmp walk to monitor the resource of my device.Can someone help me?Thanks to all,Damiano
Newbie here.I have two vlans on a single cisco switch. Vlan 10 is is getting its ip address from the dhcp server and internet access from a sonicwall firewall.I added Vlan 20 to that same switch. These two vlans will not or should not communicate wi...
Resolved! PPPoE over VLAN configuration
Hey there, I have Cisco ISR 900 device. I'm trying to pass traffic from my vlan 10 via dialer 1(ppoe client).When i tested ping from dialer 1 it works but i can not combine dialer and vlan.Can anyone see what i'm doing wrong? Config in spoiler:Spoile...
Resolved! Change ip address expression
Hi We have devices ip address like this 10.1.1.2-4. Anyone can help to show python commands to let ip address like 10.1.1.2, 10.1.1.3, 10.1.1.4 ? or below, Thank you10.1.1.2,10.1.1.3,10.1.1.4
In PI3.10 I am trying to install fix PI_3_10_1-1.0.25.ubf.However this message appears "UBF with new version of update 'pi310_mrx' misses version '0.8.23' that was previously uploaded" and install fails.Has anyone experienced this?I am running build ...
Resolved! Add ip address to python
Hi We have ip address like below. 10.1.1.1, 10.1.1.210.1.1.1010.1.2.1How can we change it into the below way, which we can input into python? Thanks'10.1.1.1' , '10.1.1.2''10.1.1.10' ,'10.1.2.1'
Hello i need your advice, im practicing LAB environment where Router act as DHCP server and using sub interface to Switch 1 and then from Switch 1 To Switch 2 using Dynamic Routing IS-IS where DHCP client under Switch 2. which ip do i need for ip hel...
Resolved! mac access-list ISR4221
HI,My name is Alexandre, I'm from Brazil. How to configure ACL by mac on isr4221 router. I have a router 1905, I do it through int BVI and it works.can anyone help me
Hi, We have two kinds of servers to monitor all our devices. Each of two servers has very similar ip address with each other. Engineers add new ip address to one of the two server sometimes, other time add ip to other server, which make the ip addres...
So, there was fiber being done prior to these going down. These are IE-4000-4GC4GP4G-E switches inside traffic light control cabinets and they are daisy-chained. The switch prior to this one was down, but then came back up but isn't showing the downs...
Ok so this is going to be kinda of a book on Netflow and some very useful items I also have some issues with the setup. So lets jump right in. I have a Cisco 9500 and it is used as our core user switch. it connects to our data coure switch which conn...
Hello Team,I'm unable to add C9300 Series Switches in Cisco Network Assistant Version 6.3(4)kindly help me out on this issue.Thanks in advance!!Best regardsDevender Budhiraja
Resolved! PI not start - java error
Hello, I got a java error, see the following text, if I tried to start ncs or check status: ncs statusException in thread "main" java.util.NoSuchElementException at java.util.Scanner.throwFor(Scanner.java:862) at java.util.Scanner.n...
