Network Management

Resolved! Cannot modify or create EtherChannels for Catalyst 3750G-48TS in CNA 6.3

I receive the following Java error when attempting to view existing or add new EtherChannels for our Catalyst 3750G-48TS switch stack in Cisco Network Assistant 6.3 Can someone help me here? Our Catalyst 3750G-48TS stack of 7 switches is currently o...

MATLAB1 service is down and an attempt will be made to automatically restart the service - After install PI 3.1.5 Maintenance Release

Dear all After installation PI_3_1_5-1.0.44.ubf - PI 3.1.5 Maintenance Release. to Cisco Prime Infrastructure 3.1 Virtual Appliance image i have Major alarm on my Cisco Prime infrastructure and some modules are not working.I was tried restart this ma...

Prime Alerting

Is there a way to removed interfaces from being monitored? I keep getting alerts for interfaces that will never be "UP", but I don't where to remove them from that alert setting.

SNMP IPv6 issue

Hello i am receiving the following error while adding a Cisco ipv6 device in prtg server Sensor does not get response from device. SNMP credentials are wrong or device does not support the required uptime OID (1.3.6.1.2.1.1.3.0) for traffic sensors....

Monitor cisco switches via snmp

Hey guys, I have a silly question: I have some catalyst 2960 and 3850 switches. I would like to monitor them with snmp. But where do I get the OIDs? Or how can I find them out? For example for monitoring the fan status, power supply status, temperatu...

PFRV3 mib support for Cisco IWAN

Hello, I would like to know if pfr mib is supported in IWAN environment to get the path details. Regards, Sri

Cisco Prime 3.1 no email alerts

HI I have recently built a fresh PI 3.1 (due to issues with a 2.2 upgrade) and then re imported devices and maps. Now, email alerts are not working and I cannot figure out how to make them work!!!... > I have filled out the SMTP server details an...

In need of help on Netflow configuration on the new ISR4000

Hi there My company has bought ISR4451 router as a replacement of ISR3800. It was easy and simple to configure netflow on the old routers like; ip flow-export source Loopback0 ip flow-export version 5 ip flow-export destination 10.19.14.22 9996 This...

Resolved! CISCO Prime 3.1 Inventory Change Report

I remember in LMS 4.2 there was an inventory change report. Do you know if there is something similar in Prime 3.1? I had a problem when i realized that some devices that were added in the Cisco Prime 3.1 were accidentally (?) deleted and i found it...

Resolved! Need to add wait of 120 seconds before sending email

Hi, I would like to add a wait time of 120 seconds before sending email using EEM script. This would give enough time for the failover convergence and ensure email is sent using the backup link. Below is what i have configured so far. Also i would...

Anyway way to determine what software versions will run on which Cisco hardware platforms

I am often looking to remdiate vulnerabilties across our cisco estate. One vulnerabilty I am working with at the moment is trying to address machines on our network that are running telnet. To remediate this I am looking to enable ssh and disable te...

Get the list of VRF names configured on Nexus N9K via SNMP

I run an app that gathers all IP subnets ( IP addresses, subnet masks ) configured on all network devices worldwide within our company .It uses SNMP. I would need to add IP subnets defined in non-Default VRFs on Nexus N9K switches.I know how to query...

CISCO-STACK-MIB not working on Catalyst 6500 VSS?

We have Cisco Catalyst 6500 VSS switches running IOS 12.2(33)SXI14. To my utter amazement I found that these switches seem to no support CISCO-STACK-MIB even if they should (according to MIB Locator). spam@l5nets02:~$ snmpwalk -Lf /dev/null -Pd -OX -...

CPI3.1.4 DP7 unsupported cisco device for N9K-C9372TX-E

Hi all, i've CPI 3.1.4 DP7 installed and when discovering N9K-C9372TX-E the CPI recognize them as unsupported cisco device. after reading in the device supported i found out the N9K is suppose to be suppurated from any NX-OS version. does anyone ha...