I'm trying to upgrade a new ISR 4431 from 3.16.6 to 16.9.2. When I copy the file from my SolarWinds SCP server, I get an error that the file failed to open. Here are the troubleshooting steps I've taken: -Try on another SCP server. I tried to copy ...
I have third party devices which I want to monitor/manage them through cisco prime infrastructure (CPI) 3.9. I will ask the vendors to send me the MIB file but what should be the extension of a MIB file so it will be compatible with CPI 3.9.
i did a basic configuration of my cisco Catalyst when i save the configuration or don't save the configuration, my enable password doesn't work. i have not set anything but the hostname and a vlan up, i can't get passed this part? any help why my ena...
When I tried to connect ASR 9000 router using SSH, I got the following ssh debug logs. ~$ ssh -v username@xxx.xxx.xxx.xxx OpenSSH_7.2p2 Ubuntu-4ubuntu2.4, OpenSSL 1.0.2g 1 Mar 2016 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /et...
I have a Catalyst WS-C3750G-48TS , I am not able to telnet into device - i don't know the passwordi am not able to take switch down , this is my core switch. Am I able to backup current configuration using web interface? I am able to access web int...
Hello,I'm curious to know if there is a way to filter out specific logins on Cisco 9200/9300 switches. I would like to filter out the user VanDeesel because they log in every minute or so to pull data. However, I would still like to see if other user...
Hi All,Wanted to know what is the best practice in monitoring the user's port of the core/access switches. We are flooded with alerts in our monitoring tool.
Hello, we are trying to monitor the interface BW of a Nexus 7K but it does not show anything. We are able to see CPU,mem so SNMP between the PI and N7K would be ok. I we verify the credentials on PI are ok. It is simply SNMPv2c. Nexus version:8.3(2)...
Hello geeks,i have an issue, every time i try to start my DNS i get the below errorsfailed to read /var/nwreg2/local/data/cdns/root.anchor.error in trustanchors configcould not apply configuration settings Please see attached screen shot.
Hi everyoneI have a problem with updating EPN manager.In my network I already have an EPN server installed as primary with version 5.1. We are installing a second server in HA mode, this has been configured as a slave, the two servers are version mis...
I have Cisco Prime Infrastructure (CPI) 3.9 with Cisco IP phones 7962, 7965. Although these phone do not have SNMP support so I can not manage them, but why they are not showing up in CPI "network topology" to be monitored on the basis of IP or MAC a...
I have a qeustion about RTS/CTS packet.before asking, there are 5 clients and 3AP.Clients roam around and communicate with multiple APs.Example)When the wireless communication is working properly, Client1 sent RTS packet to AP. and also AP sent CTS p...
Hello,I am trying to configure the management interface on the back of a Cisco 4331 router and am having a hard time wrapping my head around getting it to work. I read through the 6 page Cisco doc "Configuring ethernet management port" and it seems ...
We have configured SNMPv3 with AES256 encryption in Cisco routers available in our network. However we see that devices are unable to manage from NMS if we configure with AES256 whereas with AES128 its getting discovered properly. Even we tried snm...
Hello I have a Cisco IE3400H. For some reason when I plug my PC in you'll see it try to connect, then it disconnects. It just keeps spamming between "Identifying" to "Unplugged". I have another PC and that one connects just fine with the same exact I...
