Network Security

Hi all,i am running cisco idsm-2 version 7.0(E4). health sensor is under critical conditioni can see "Processing Load percentage = 100" under show stasts virtual-sensorand also receive overruns on the one of the interface.can  anyone explain me how t...

Hi All,I had a problem:-I am having ASA 5520 & a static natting is applied on it.static (inside,outside) 115.112.246.55 192.168.1.163 netmask 255.255.255.255object-group service reseller tcp port-object eq wwwaccess-list acl_outside extended permit t...

Hello Experts,I have been doing some reading. I will set up a Dhcp server on the inside interface of my pix.  I would like to have the DHCP Server authenticate to the Active Directory Server that is located on the DMZ.Inside --pix--dmzInside interfac...

Following situation.ASA 8.2 NAT/dns statement:static (inside,outside) tcp interface smtp 192.168.0.1 smtp netmask 255.255.255.255  dnsHow can I reflect this static in 8.3?I only do have the "interface" as the ouside IP!

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm ...

Hello Dears,I have a 2 No's NAC Manager and 1 No's NAC server, Our Network is Cisco three tier:  Access> Distribution >Core. Distribution switch is doing inter vlan routing and layer 3 connecting (OSPF) between the core and the distribution and amoun...

Hello,Whenever I pathping or tracert from my PC through the firewall to other VLAN's (sub interfaces) or VPN's, where don't see the IP's appear like below, we just get  lots of *, Iguess it is just hinding itself.  Can I get this to show?If I pathpin...

Hi Folkswhat  the steps to migrate form engine-1 (ips 5.1) to engine-4 (ips-7.0) on the aip-ssm 20thank you

We'll be implementing Cisco NAC guest server for Guest Wireless users, ( Model #3310),  the question is do we need to configure separate physical interface for User authentication requests( from Wireless ) and a separate  Interface for Guest server t...

hii m configuring Asa 5510 with nat. i have some internal servers. my clients requirement is to hide the original loacl ip of servers. thats why i using static nat. so the outside world only know the real ip(x.x.x.x), then it is natted into a server ...

Hi everyone,I implemented FWSM in trnsparent mode recently, everything looks nominal however I can't get one URL https://xxxxx:2000, ( I scrumbled it for security reasons) I beleive I can use a cutomized policy to make it work( I don't know how), ple...

Is there a way to trigger stateful (or stateless) failover on ASA 55xx (8.0.3) when there's a failure on the IPS unit? I understand the fail open/fail close and its application on a single firewall, but the better solution for an IPS failure in a red...

i have 4 or so interfaces on my asaint1 - internal networkint2 - dmzint3 internetI want to allow an outbound udp port x.x.x.x from internal to dmz.how would I do that?

AAAAAARRRRGHI have a customer we are trying to demo sslvpn just simple access to a web server.  Granted the permissions areanyconnnect premium peers 2 which should include sslvpnI have made it look exactly like an 8.2 config but no luck. When I issue...