Network Security

I have an old PIX 520, and want to do encryption with it. I did upgrade to 5.1 and properly entered activation key for DES encryption, but after reload, I don't see in show version that DES encryption is available. Furthermore, if I enter the command...

Am i right to say that PIX does not have IDS capability?

I have a pix 501 and am trying to connect it to the net via a DSL Line.IP address information is entered staticly, and the route command for the outside interface is "route outside 0.0.0.0 0.0.0.0 Outside 1" As far as I can tell everything is entered...

Here's the info:I have a wireless network that has 30 laptops. They get their IP address via DHCP from the VPN Server (Win2k). VPN box has two nicsExternal 192.168.101.xInternal 192.168.100.xPIXExternal: 192.168.101.xInternal: 192.168.100.xCorp Lan: ...

on my two DMZ i am setting up. the line is up but the protocol is down. I can not figure out how to get it up. This is a new setup. one is staight to a server and the other to 6509 switch. Any help would be very nice. My head is going to go boom.Jaso...

will the new 515E work in a failover environment with the "now-replace" 515??

I'm configuring CSPM3.0f and noticed that after adding a existing PIX535 firewall with several interfaces with the same security level CSPM3.0f doens't allow this. Is this so... or has anybody a suggestion how to solve this problem

Main Goal: To have a PIX 501 get a CA from MS CA server.. How does PIX or a router get a CA from the MS certificateserver? I understand the lines of code you have to type in on a PIX / routeri.e.path to get to the CA server but How does the CA server...

Hi Everyone,I have a problem that i need to solve. We have a 525 running version 6.11. We are trying to configure a very tight set of outgoing rules (incoming are tighter :)). Basically we have a NFS client on the inside interface and a NFS server on...

Plugged the following commands into my PIX 515 FW:static (inside,outside) tcp 1.1.1.1pop3 192.168.50.10 pop3 netmask 255.255.255.255 0 0static (inside,outside) tcp 1.1.1.1smtp 192.168.50.11 smtp netmask 255.255.255.255 0 0static (inside,outside) tcp ...

I have a PIX 515. I installed it. right now it doesn't allow me to go out to the internet and does not allow me to read my e-mail.I connected like this: Router --- FireWall--- hub---terminalsPlease give an idea of the problem.thanks

We have PIX 525 with inside, outside and DMZ configured.after some time of smooth operations, the PIX stops forwarding traffic from inside to outside. Inside to DMZ works fine. After some time even inside to DMZ traffic stops. We have to remove the a...

Hi. Looking to nat DNS messages flowing across a PIX.Seen the "alias" command, but this seems to be for DNS servers on the outside only: (ie. DNS reply is NATed on a transition from a Low -> High interface)whereas I have a DNS server on the inside, w...

Scenario: 1.Multihomed router having Serial 0 and 1 terminated into 2 diferent ISP 1 AND 2(1 for Failover). FastEthernet 1 and FastEthernet 2 has 2 different valid IP addresses A.B.C.D and M.N.O.P. We have to connect the PIX Firewall with only one Fa...

Hi, I have a setup where a PIX is installed between router and call manager. The router is connected to PSTN. But when I make a call from outside to inside only one way traffic is there, ie I can here voice from ip phone but not the other way. I trie...