Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2782 PostsActivity in Networking
Resolved! Cale diagnostics?
So I have gone through this issue, what does open mean, and how to make that normal? Interface Speed Local pair Pair length Remote pair Pair status--------- ----- ---------- ------------------ ----------- --------------------Gi1/0/13 10M Pair A 0 +/-...
snmp query to 9300 switches to find out power supply status
does any one know how to query the 2nd PS state . we use a monitoring tool called auvik and use oid for query. 1.3.6.1.4.1.9.9.13.1.4.1.2 oid is the powersupply state but if i just want the 2nd PS or 2nd switch ( on a stack) power supply states?
Expert Insights Series: Empowering Catalyst Center Excellence
Take your understanding of Cisco Catalyst Center to the next level with our upcoming Expert Insights Series! This comprehensive 4-session foundational series is designed to help you unlock the full potential of your Catalyst Center deployment, st...
Wrong DHCP relay vlan on C1300
Hi,so i've bought a c1300 to test the functionalities I need and I run into some problems.I have a a access point on port 16 with 2 radios for vlan 1 Clients and vlan 4 guests. On my old Cisco and Dell Switches I made an Ip helper-adress on the vlan ...
SCP transfer failure
Having issue with some devices not being able to save to a file server using SCP . The problem seems to be a 1 way issue so it's not a FW issue also I have devices which are the same device running the same code yet one works but one does not work ...
Interesting POE problem on Cat 9300X-48HX
I'm about to open a case with Cisco and the device maker but figured I'd try the collective mind here. I've got some non-Cisco devices using POE on various Cisco switches and they work just fine. (TASCAM VS-R265 4K Streamer/Recorder) I'm using them o...
Private-Vlan with VRRP
Hello to everyone.I am working on this topology for 2 months but i wasnt able to find the accurate solution even i asked from prefessional but their solution wasnt accurate.My qustion is ----> How i can activate Private-vlan while using SVI with VRRP...
dnacentersdk issue with getting ExcutionID vs. data
Good morning,so i have been using dnacentersdk for quite some time now, and pull a list of members of a given fabric site was pretty simple with the following commandsite_list = api.sites.get_membership(site_id=site_Code) this would typically provide...
Fabric-Site vs Fabric in a Box
Hi Guys,Operationally, and feature set wise, are there any differenes between a Fabric-Site and Fabric in a Box. My main area of thought is Wireless. Can I still have a centralised WLC that supports a distribted campus? I.E, lots of Fabric-Sites and ...
C9300 - Close SNMP Port with ACL
Hi,we have multiple C9300s with public IP addresses. They are running SNMPv3 for monitoring which works but when you do a scan from the internet / outside with nmap / censys / shodan / ... the UDP port 161 for SNMP is responding.We want to make this ...
Cisco ISR & ASR 1k Routers: IOS-XE/Firmware Upgrade (Install Mode)
NotesA Word from our Sponsors:Introduction:Section 1: General ProcedureSection 2: ROMMON UpgradeSection 3: Cellular Modem Firmware UpgradeSection 4: GOTCHA Notes This procedure is aimed at Cisco ISR 1k, ISR 4k and ASR 1k router ONLY.IOS-XE Bundle Mo...
NAT Configuration Help
I am working on Packet Tracer. I was told to configure NAT on the Gateway Router linked to Gateway Router and other internal routers.I was given this example on my lab document Assuming, you have been allocated the public IP network 200.57.64.33/29, ...
Resolved! Turning VTP off with pruning
Hi,We are planning to disable legacy config of VTPv2 on a network. Pruning is enabled on the domain. When we attempted to run "VTP mode off" on a switch at the edge of the network, we found that the upstream switch appeared to prune all the VLANs fro...
Username and password no longer working
Hi experts!I have a stack of two Cisco SG550XG 10G Switch 24 Port and everything worked fine during install and setup a year ago and also for a while after that.I have lost access since about half a year and the configured username and password has s...
Need to use an IP from an ISP provided /29 on another device for egres
i have a cisco 4431 connected to my ISP. the ISP provided a single /29. I need to use an IP of the /29 on the WAN port of another device for Internet egress out that device. how can i share (VLAN) the /29 since the 4431 is receiving the /29 on a r...
| User | Helpful Count |
|---|---|
| 42 | |
| 36 | |
| 34 | |
| 20 | |
| 19 |
