Resolved! etherchannel
There shouldn't be any reason not to be able to cascade switches using both gigabit ports etherchanneled (half duplex), right?
There shouldn't be any reason not to be able to cascade switches using both gigabit ports etherchanneled (half duplex), right?
We have a remote site that we are going to have two Point to Point T1's to from our main site. I would like to combine these lines into one logical line. Would I use Multilink to do this? Could someone please point me to some documentation on this?On...
Hi, I need some help with the configuration command to setup PAT, so that all users within my local network will use a single IP address out on the internet.Thanks in advance.
HelloI have multiple Automated Teller Machines connecting to a Cisco 2620XM router acting like an x25 PAD and translating x25 sessions into TCP/IP ones.Five ATMs connect properly to the router, but the sixth one fails with the following debug output ...
Hi All,First of all i need to understand the features provides by Cisco Works 200.I have following devices in the network.Layer 2 3500 and 2900 Switches.Layer 3 6506 Switch.Router 2661 and 3745.PIX 515.In the event of broadcast storm can cisco works ...
I have a cisco 3640 router and a cisco pix firewall 515 running 6.3 ios. I am not able to access some website like www.verisign.com..., but when i give any public proxy server at my IE settings then these websites are working. We had web marshal(URL ...
Is there a doc somewhere on Cisco's site that lists the software features available on the 2950s and whether that feature is part of the standard image, the enhanced image, both or none?
Hi,I am looking for a specific software that manages network status specially for the hubs and switches btw we use Cisco 2950 switches on our network.. Is Cisco Works 2000 is the best choice for these needs..Or can you advise me for the best solution...
Hello,I want to establich an emergency backup line for the case our WAN chrashes etc.My idea:(my network)>cisco1721-with nokia30 connected------dial line-----------nokia30-with cisco1721 connected>(my remote network)How do I connect a Nokia30 with a ...
after a power failure the catalyst 4006 supervisor II engine boots to rommon only.i downloaded a new catos image and still boot to rommon .and this type of catalyst doesnot have an external flash or a xmodem command to download the new image to the c...
HiI have a couple of 3662, both having NM-16 modules and single WAN interfaces. They are running IOS version 12.3(10). They randomly crash at diffrent times. I thought it might be a hardware issue, I replaced the boards with no luck. I would be grate...
Hi,are uplinks in the redundant supervisor active ?And can be used for data if in the forwarding stp state ?
Hi Does the catalys 3500-XLsupport 802.1x ? Is there any link where in I can get a list of catalyst switches & IOS supporting 802.1x ?RegardsHrishikesh
We have a site with a Cisco Cat 4006 with a WS-X4232-L3 in slot 2. An HP switch is connected to Gig 1 and a file server is connected to port Gig 2 (in other words, an HP switch is is physically connected to the Gig 1 port on the front of the WS-X423...
I have a spare 6509 that I need to setup. I am used to working in the CatOS and the native IOS is throwing me for a loop. Does anyone have any sample configs showing inter vlan routing, vlan's, STP, and any other basic config ideas. I appreciate the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |