I think the answer is "no", but does anyone know a way to autodisable a port if its status changes too often?Cat6000, I do not know SW version.Thanks,Paul.
I think the answer is "no", but does anyone know a way to autodisable a port if its status changes too often?Cat6000, I do not know SW version.Thanks,Paul.
I have a Network Instruments Probe attached to a port on a 6509 running IOS. I want to span a 100Mb port to monitor traffic on another 100Mb port on the same card. The problem is, that when I define the destination port, the protocol on the des...
I am currently working on a large corporate network replacing its legacy equipment with new Cisco devices. I am debating on what the best design would be for laying out the VLANs. In the past Cisco has recommended using end to end VLANs which see...
Hi,everyone,I have a question:information-based of "cisco 7XXX show diag", how to know which one VIP type ?Router#show diag 10Slot 10:Physical slot 10, ~physical slot 0x5, logical slot 10, CBus 0Microcode Status 0x4Master Enable, LED, WCS LoadedBoard...
Hi fellows,could someone help me with problem withour counters on C2610.We observe that our counters on C2610 and PIX grow rapidly. Both are connected trough 3com switch.Have someone any suggestions.regjl
I hv a problem with remote access which is slow response to authentication.From start remote dial-up to established a connection. it took around 36 second. I must speed up the initial process because a lot complain on this. Pls advice.
Hi Dudes, I am going thro bgp study guides. i knew that bgp is inter AS ROUTING PROTOCOL. it is used between ISP'S for policy based routing . my qn is when corpotates (not ISP) need registered AS numbers and need for bgp. why they should get AS N...
hi,i found 2 different statements about the max number of vlans on a cisco 2940. The Product overview tell maximum 4 Vlans, but the online Documentation tells me max 12 Vlans. What is the maximum Number of vlans on a cisco 2940?
Any idea how to start every day same job seven times a week. Now you can only choose immediately or once when sceduling a job for devices. Need to run job that put shutdown ports every day at evening and run no shutdown in morning.
Hi all,I have a 4000-M Series router with a 4-port serial card (NP-4T).I want to know if this serials ports supports E1 connections speed using a E1 csu/dsu.If not what serial card I have to purchase?Thanks in advance,Regards,Carlos Welhous(809)334-7...
what is bus enabled module and crossbar fabricwhat these thing means?32-Gbps busAllowing access to a central shared bus 256-Gbps switch fabricLocated on the switch fabric module (SFM) 720 Gbps switch fabricLocated on Cisco Catalyst 6500 Series S...
Hi,I am having 1> Two 6506 Back 2 Back connected. Having Hybridge IOS.2> Nine 3508 at distribution.3> 90 3512+3524+3548 Switches at access layer. From last few days I have started facing high broadcasting problems. Is there is any Latest IOS which wi...
Hi,pb: card 16 AS ON Router 3725 not supported, what to do.Upgrade ios ?
I'm missing something here, but can't see it. Why is the following access lists, when applied to the interfaces, blocking the ability to resolve by name?access-list 1 permit 10.0.0.0 0.0.0.255access-list 101 permit tcp any any eq wwwaccess-list 101 p...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |