anyone can tell me about reverse telnet/traceroute. what benefits i can get out ot it. how to do it?
anyone can tell me about reverse telnet/traceroute. what benefits i can get out ot it. how to do it?
Hi,I'd like to find out if it's possible to have an isdn line to connect to 2 remote sites using 1 B-channel for each site.How do I ensure that at any one time, only a single B channel is connected?What I'm trying to achieve is to use 1 channel as a ...
I have a new router and when I try to boot it, it just continually cycles through the boot process and shows the following Does anyone know if I can fix it or is it a hardware fault?System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1...
hello alli have a strange problem, my organization website is working to the outer world but it is not woking inside the network. can anybody help please
Sorry in advance for my newbie-ness. I've got a 56K frame relay line that the phone company says I'm putting about 86K on. When I get on my router, (hyperterminal) it seems like I can find out tons of info - but not the actual traffic in/out of ...
I believe only one GIBC port on Sup IV in 4506 is active and another one is in standby mode (no traffic can pass through at all). Can anyone confirm this? Or both GIBC ports are active?Two GBIC ports on SupII in 6509 are active. So if I have 2x SupII...
I want to know that why we use secondary IP address on ethernet interface. What is its benefits to use it. Pls also help me that is it possible that i can route traffic between 2 net IDs on same segment with the help of router's one ethernet 10bt por...
Hi dears is there any dealer of cisco products, Cables routers and etc in Lahore Pakistan.I have searched a lot. Would anybody pls help me in this regard.
HUB1|CA HUB2T |5 |<-- Fiber| |Switch1 --- Switch4 | |<-- Fiber |Switch2 --CAT5> HUB | |<-- Fiber |Switch3 | |<-- Fiber |Switch5 (NEW)In the above illustration:All switches are connected by fiber.All switches and hubs are populate...
Hi all - I run a small group of programmer types (not the networking group). We have our own simple network (tied to the main site network) with a few servers, clients, etc. We are using two 2950 switches that worked fine out of the box. Turned th...
I want to know that what is difference between source route bridging and tranparent bridging and all other types of bridging. Pls provide me help in easy way with example. I will be thankful to all of u.
How an ISP access server accept calls from more than 300 to 400 dialup users simultanously. What special devices they use to accept this amount of concurrent calls on only one number . I am confuse that how they use 300 external modems to receive cal...
Hi all - I run a small group of programmer types (not the networking group). We have our own simple network (tied to the main site network) with a few servers, clients, etc. We are using two 2950 switches that worked fine out of the box. Turned th...
Hi, what would happen if a port on a switch (2950)was configured as vlan 3 and had a hub (non cisco) connected to it? would all the clients in the hub be placed into vlan 3? or is it not that simple.
Hi AllI have a Pix, int he inside I hve two private networks, and I have two global and two NAT as:global outside 1 200.9.172.2 global outside 2 200.9.172.3nat (inside) 2 192.168.0.0 255.255.255.0 0 0nat (inside) 1 10.24.54.0. 255.255.255.0 0 0I have...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |