Other Network Architecture Subjects

Tested on 7513 PA-T3 to connect to remote site via 7200 PA-T3 no issue. Line is up. Tested on 7513 PA-T3 to connect to remote site via 3660 using NM-1T3/E3. AL Alarm. Line is down. Below is my sample config 3660card type t3 1!controller T3 1/0!inter...

Hello,I've a problem with a serial connection. I've a 2500 router connected with a Catalyst 6509 through a 2 Mbps serial line.The download transfers to the router side are perfect, with rate up to 250 KBps. But on the other direction (uploading) they...

Hello,When i am trying to follow the procedure of 'recovering password' on Router 3660, during booting, it displays message that "PASSWORD RECOVERY FUNCTIONALITY IS DISABLED". I guess this is due to the wrong registry setup. Becasue of this, I am not...

We have a campus network with several inside routers, segmenting our internal LAN. Access to Internet is provided by a 7500 router with BGP connections to two ISPs. Behind the 7500, we have another 7500, and behind the second 7500 we have other route...

Hi When setup snmp trap 3524 switches, we get a lot messages, like: Fa0/3 DOWN c3524-08 Fa0/3 UP c3524-08, PC connects with 3524 switches port, not reboot and it is using, still get a lot port up/down messages. We have lines for snmp...

I have implemented BGP multihoming using 2 7200VXR routers and HSRP in the ineer side. Every thing is working right but i want to implement a failover mechanisum for my ethernet(inner)interfaces.What i want is that if one of the inner int on the rout...

I am looking for some helpful insight on what you might do in this situation. I have a very good idea on what I want to do, BUT I am looking for different ideas. I am looking for the different ways of doing the same thing. Plus the recommended way of...

I am having difficulty getting my Cisco 837 to connect to BTconnects broadband service: relavent configuration section follows:interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl o...

Company is getting 6 leased lines. 2T1s from ISPA, 2T1s from ISPB and 1DS3 from ISPC.Requirment is I want to use DS3 as a primary connection and 4T1s as a backup. Can anyone advise me the easy approach.We have 3 Routers. One router is connected to IS...

I have the following issue:-When I stop receiving a RIP route is there away of stopping Advertising a route ?Example:-I redistribute network 192.168.2.0 into RIP (Version2) via a static route.When I stop receiving a RIP route of 193.1.2.0 I want to s...

Hello,I am trying to configure multicast on a C1750. Mu router has 2 sub-interfaces (0.10 = gateway to my server, and 0.23 to my client):1/ I have activate the multicast:no ip domain lookupno ip bootp serverip cefip multicast-routing2/ I have configu...

Hi! Which traps are supported in CW2K RWAN and is it possible to view rtr trpas generated by IPM!THANKS FOR HELP!!!!RegardsEnes

Hello,I'm transfering files from routers and switches to a tftp server in a workstation. Then, I would like to know if there's any limit about the rate to transfers from the router itself or it can transmit at the same rate than the workstation attac...

vlan problem,7507-01 and 7507-02 hsrp on subinterface vlan 105 not work properly,3550 can't find 7507-02 by cdp(7507-02 can find 3550 by cdp)show standbyFastEthernet1/0/0.105 - Group 4 State is Active 2 state changes, last state change 2d21h Vir...