The dynamic configuration tool let me place a NM-4T1-IMA in a 2651XM config as recently as yesterday. Now it doesn't show up. The compatibility matrix shows this NM is good to go in a 2600. What's wrong here?
The dynamic configuration tool let me place a NM-4T1-IMA in a 2651XM config as recently as yesterday. Now it doesn't show up. The compatibility matrix shows this NM is good to go in a 2600. What's wrong here?
I have just got VMPS working on our network, and I now find that Wake-on-LAN no longer works. I guess, if I think about it, that should have been obvious. When the PC gets switched off, it bumps the port, and so loses its VLAN membership. It's a pit...
I have tried to install CiscoWorks2000 CD One 2nd Edition on solaris 2.8, but it was finished with errors like as "./jre/bin/jre: cannot executeno new.depend fileERROR: Cannot make list of packages for installation."installation is possible or not ?
I am having a problem getting a dhcp address on a 3550 interface from a Cable Modem provider. It seems they statically map the Mac Address. I need to change the Mac Address associated with the interface to the Mac they have statically set. Can thi...
Trying to connect a 10/100 port on a C2924M-XL-EN to a 10/100 port on a C2950C. Am using a cross-over cable between RJ-45 ports with matching speeds (100) and duplex (full ) on both Switches. I removed Spanning-tree portfast on both ports. I can not ...
There is a communication between 2 different CISCO switches and this connection is configured as "set trunk off" and "set vlan 2".We'd like to know with there is some advantage or disadvantage to configure it as a trunk using just one VLAN between 2 ...
We've got a small network with a webserver in the DMZ behind a PIX 515. We are planning on adding some more webservers in the DMZ for load balancing. How do we load balance between servers with only one IP address? What technologies are available ...
Hi there, what will cause the HSRP to stop functioning? One of the interface were configured with HSRP but the standby IP is not working. Any leads?thanks!
I have an isl trunk setup between 2900XL switch and 3640 router. Switch has IOS 12.0(5.3)WC(1),and router is running 12.1(5)T10. On switch after every 10 seconds 1 CRC and 1 input error is incremented and the keepalive is also set to 10 seconds. Plea...
The MTU size on the interfaces are set to 4470 and I'm trying to make my network generate BGP update messages of size 4470 and successful in doing that but I don't want BGP marker to seperate the NLRI list into chunks of 252 bytes even though all the...
Is it true that Cisco has declared 3661(AC) multiservice router obsolute? If it is true which region are they obsolute?Thanks in advance.
I have an internet access through a 64 k leased line using NAT Technology.The Nat configuration is as follows:=====================================================-------------------------------------------ip nat pool Internet_Access 62.192.x.66 62.1...
Hi!!!Can anyone tell me why when you configure a serial link (T1) with encapsulation ppp and you issue a show ip route always appears for that serial 2 routes directly connected: the one that you configured, and the other side link as a host route (3...
Why I can not apply Policy Map to Sub interface?R2_2611XM(config)#int s0/0.105R2_2611X(config-subif)#service-policy out mytest CBWFQ : Not supported on subinterfacesR2_2611X(config-subif)#
Hi,we have following problem with a WS-C2912-LRE-Switch and 575-CPE-Modem:We tried to connect another switch by using a LRE-Line as trunk with 802.1q-encapsulation in order to have various VLANs on this switch (No fibre to this building).That works, ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |