I am having 6 2950T-48-SI switches. These switches have 2 1000BaseT ports instead of GBIC slots. Will I be able to stack them like other 2950s. If so , how?Regards,Tijo
I am having 6 2950T-48-SI switches. These switches have 2 1000BaseT ports instead of GBIC slots. Will I be able to stack them like other 2950s. If so , how?Regards,Tijo
Hello, how I can verify whether an ATM PVC on an LS1010 "dropped cells". I can do on the controller, but I did not found any possibility to verify it per PVC.Te command "sh atm vc int atm x/y/z [vpi] [vci] " show me the Tx an Rx Cells, but no dropped...
I have a T1 between remote sites that have two separate networks at each end of the T1. We do not want to co-mingle the networks for security reasons and have been suggested to use the 1721's.A vendor gave us a quote for 1721's,WIC-1DSU-T1's,WIC-1ENE...
Are there MIBs to collect the following output:?5 minute output rate 2000 bits/sec, 3 packets/secThis came from a 2900XL. I know I can collect octet outputs, errors, etc, etc.I would like to have an SNMP trap when packets/sec exceed x amount, within...
Hi every one ..I'm looking for a solution, that can make a graphical view of the status of our BGP sessions , If a BGP sessions changes status, I need the graphical view to change, so our NOC can see witch BGP peer is up / down ..Best RegardsPeter
I'm new to cisco and i have a router 2600 series which i want to use in my network. I will like to use the router as a dhcp server. I have othere servers which will be attached to it. this is how it looks in the attached diagram. Please could some...
I am trying to install the broadband access center for cable 2.5 version on a solaris 8 system and having problem during the installation.I have upgraded my system with the J2sdk patch cluster and my system is at level [Generic_108528-27]. Some of th...
I keep getting traps from two of my switches that indicate interface 1 or sc0 is down, but I cannot figure out why. The other local switches do not have this problem.
Does anyone know if the CISCO aironet 350 can bridge ethernet through its console port.?
I am having problems setting up a TFTP service on my router. When I type TFTP-Server it gives me a list of: Flash, Null, System, Xmodem, Ymodem, etc. I chose all of them at one time or another and it always gives me the error: cannot find"whatever" i...
About this conversation:"Etherchannel newbie Mar 14, 2003, 10:46am PST can etherchannel span 2 boxes? Can you have port gig0/1 on switch A and port gig0/1 on switch B belong to etherchannel 1 if A and B are connected and terminate at C. " About this ...
a cat4908-L3 connected to a cat2980G via G5484 and a pair of multimode Fiber. the cat4908g-L3 log errors about every 25s. Jan 21 14:30:54: %AAL5-3-RXERR: Flow Hdr: (10) input packet dropped because of CRC errors
I have dual 6509s with dual sup720s and am having trouble with HSRP. The configurations automaticaly sync so a different priority for HSRP cannot be given to the second MSFC. I did some research and used the Cisco approach of the "alt" command for t...
Hello,Can someone explain me how does this fonction works ? The feature overview of http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guide09186a0080087c4c.htmldoesn't give so much explaination.Regards,
Hi,I want to read de Mac address table of the following switches models. 6500, 3550, 2940 and the 3548But i can't find a useful OIDCan you help me, please
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |