Dear Friends,I have a frame-relay small network with a star topology. Core router is a 3640 and 7 branches use 1750.Core router has 7 subinterfaces point-to-point configured in one an interface.5 branches have subinterfaces in their interface and...
Dear Friends,I have a frame-relay small network with a star topology. Core router is a 3640 and 7 branches use 1750.Core router has 7 subinterfaces point-to-point configured in one an interface.5 branches have subinterfaces in their interface and...
Is there a Cisco switch that we can assign an ip address for each port ?Thanks,Derrick
Can match access-group be used to match traffic within an IPX access-list ? Or is the match access-group used for IP only ACLs ??
While I was troubleshooting some low latency with some of my routers, I found out that ping times between the serial and ethernet interface is 44ms or even higher.I would think the times would be around 1-2ms and not over 40ms!!! What could be the c...
I want to perform tests about ISDN connections and have 2500 series routers with ISDN BRI (S/T) interfaces. Is it possible to connect these BRI interfaces back-to-back or how a testing senario may work?
has anyone experienced problems with CW when it's behind a firewall? either hardware or software? We are looking to use a Netscreen 5XT.thanks
I have a problem with the connection whereas at my office the line protocol down but the remote office is up but the dsr& cts down. line provider provided the hardware loop from remote office and i can see my line protocol up- need your help to isola...
Hi !I am a little bit confused with this reg. expression:ip as-path access-list 3 deny ^[0-9]+ [0-9]+ [0-9]+ .+$ip as-path access-list 3 permit .*As far as I understand the first line says that the string has to look like :xxxxx xxxxx xxxxx sd334s sd...
We have a headend 3662 router with a HSSI interface terminating 3 T1s (muxed). This router support 40+ remote sites and is over-subscribed based on total remote ports that it terminates. It is obviously not over subscribed based on CIR. We need to ...
All,I have a router which connects to as10, as11, and as13. There are multiple routes in as13 that i want to summarise to as10, and as11, and there is mutual redistribution ocuuring on this router.Now, when I enter the command ip summary address x....
Hi, i am having some trouble configuring a 1721 with 1 BRI to dial into a 2612 with a PRI adapter. It seems that something is going wrong during PPP on the 2612, authentication is OK and it gets a route to install via Cisco AV-Pair from our Radius (A...
I need to set up an ISDN BRI connection between 2 sites. Which is the best router to use.Thanks
Configuring RIP - Network statementI've got 2 interfaces on 2 devices.172.18.140.2/2410.16.15.3/24I want to enable RIP.To configure RIP what would the network statement be for the above IPs.Would it be :Router Rip Network 172.18.140.0Network 10.16.15...
hi all,we are using 3662 router with NM-16AM card for our dial-up user.anybody know how to identify the user telephone number.is there any link or any configuration for that.pls let me know as early as possibleregardssan
Duplicate IP AddressesWhich command would indicate Duplicate IP Addresses:Sh interfaces or sh logging??Thanks in advance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |