I had missed the above session due to unexpected emergency calls. REquest you to upload the videos at the earliest
I had missed the above session due to unexpected emergency calls. REquest you to upload the videos at the earliest
Hello,I have stacked 6, 2960x switches with the supplied 0.5m FlexStack cables, however my "sh switch detail" doesn't match up to how it's cabled. I found documentation on how to cable 4 of them with 0.5m cables, but not 6. Could anyone explain or po...
Dear All, I had tried IPsec with fast Ethernet 0/1 it works fine but when i tried to map same ipsec crypto to tunnel1 {VTI} interface IPsec not working. My remote Site checks for source IP of fast Ethernet 0/0 {Proxy ID in Juniper} I tried to MAP c...
I am attempting to create an alarm for Port not Forwarding and using the Major alarm relay for a port. When I apply the changes I make on Cisco Network Assistant as well as through CLI, the changes I made are not saved. I am doing this all under a ne...
Hi Guys, apologies for the noob question, but totally new to Cisco never come across it in anywhere i have worked, want to start learning it, anyone got a good starting point?Phil
(SNTC-CSPC2.3.1.1-RC4-Build_OVF10_1)PSS
Good night.I wrote because I have a problem in my company, because when I restart the main switch, enter rommon mode, my computer is a 6509, Cisco Catalyst 6000 Series Switches, 12.1 (13) E10.*** System received a Software forced crash ***signal = 0...
3750 IOS 15.0(2)SE4 tacacs when issuing tacacs-server host X.X.X.X I receive "the cli will be deprecated soon" I issue the same command on a device with 15.0(1)E1 and it works.
Hi Team,I am newly joined Network Engineer.I don't know how to prepare Network Diagram or Network Design.Can anyone please help which tool are used to draw the diagram for networking.Because we are planned to design New DC.So I need to draw the diag...
Looking for ways to set Flow Control for a vNIC without impacting other vNICs. The intention is for configuring Oracle 11gR2 RAC private interconnect.
I am attempting to add a Domain to our Cisco CDA appliance. I have made all of the modifications recommended on the install to the Domain Controllers, but it will not communicate. I am getting the following error in the log: org.jinterop.winreg.smb.J...
Having trouble migrating from a 4506 classic with Sup 4 to a 4506E with Sup8E. Cannot get the dot1q trunking to work. Any thoughts?This is the config on the old switch:interface GigabitEthernet2/27 switchport trunk encapsulation dot1q switchport tr...
hello there, how to design a small and medium networks from the scratch
Hi,We are coming with 3750 stack switch upgradation. I am facing below issue.Master 3750 is of 16MB flash & Slave is of 32MB flash. Can i upgrade this stack as i have to use image of 17.5 MB.Do i need to upload the image on both maste & slave? if so ...
Hi all,I have a topology as below. I named links as A link (R1-R2-R4), B link (R1-R4 direct link), C link (R1-R3-R4). At first I want only link A and C to be used while loadbalancing for network 4.4.4.4 (Anounced by R4). If any of these links will fa...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
03-20-2023 08:49 AM | ||
03-20-2023 07:11 AM | ||
03-17-2023 07:38 PM | ||
03-16-2023 03:48 AM | ||
03-14-2023 01:40 AM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 |