I want to configure VLAN, my router support encapsulation dot1Q. Can it work if I only have a hub. ?.
I want to configure VLAN, my router support encapsulation dot1Q. Can it work if I only have a hub. ?.
Hello, I am hoping someone out there does not mind lending a newbie to BGP a hand.I have 2 sites, A and B. A is our primary site with a full Class-C 205.205.28.0/24routed to it. Site B is our DRP site with a half Class-C 65.201.200.128/25 Until now...
HI All,How can I enable access-list by MAC addresses in 3600 router. I want to deny some MAC for services like telnet/ftp.Thanks for your help.Richard
Hello all, I am searching for a mid-range LAN router like the 2691 series that can handle Gigabit over copper. I've heard that the lowest-end router that can handle GIg over copper would in fact be the 2691, 3660, 3725 and 3875 routers. Doe...
We have a cat 4006 with SupIV running enhanced layer3. I don't want route to advertised to the one of the router connected to the switch. Is there an equivalent passive-interface command for switch?Thanks...
I am having the worst luck with creating an ISL trunk from a Catalyst 6509 to a Catalysty 2948-L3. My problem area is the configuration on the 2948g-l3. can someone please help with an example or anything...Thanks
Hi Do you konw when I need Cisco IOS ENHANCED L3 o Basic L3 on Catalyst 4507 SUP IV, and if I really I need it.
I want to give a limited class of service to 1 subnet allowing only protocols like http, pop3, smtp and blocking or limiting everything else like kazaa, etc. Im running a 3662 with IOS 12.2(15)T1 (IP Plus) What would be the best configuration to acco...
Hi !.Iam using Cisco 7507 with FrameRelay for data connectivity.Iam making use of subinterfaces.Each Mail interface has many subinterfaces and each subinterface corresponds to a PVC.How can i acertain the Utilization ( Input/Output Rate) for a speci...
The issue that i'm having is that i'm trying to setup a VPN between two dsl customers but the two cannot ping each other. Basically i have the BVI setup with an ip address, lets say, "1.1.1.1". Business A has a Linksys DSL/VPN router with an ip add...
Hi:Donno if this is possible but thought I might ask the Gurus....A customer has a satlink between two sites. Its a 256 K line that has VoFr configured. Now the ques, can we break that into 2 pipes , 1 running VoFr and the other IP. If yes, can you p...
all-yesterday , while deploying a new 4506, I had the strangest problem. when booting up the switch i had no access to my modules below the sup module - and vlan 1 showed up, down. the router was fine, but the switch needed to be rebooted several t...
Is it possibel to recover or reset the dba password for CW2000 RME (3.4)? I'm on a system installed by someone else not around at the moment.Michael.
Sorry if this is not the right forum. Could someone tell me the part names, part numbers, and/or where to buy the green 2 and 4 lead dc power connectors for the 1900 and 2900 switches. I assume that other products use the same connnectors.Again, thes...
Sorry to ask such a basic question but! 1721's are considered an answer for the small and medium-sized businesses, but what does Cisco consider a small to medium sized business to be. I realise there are a few factors to be considered, to many to go ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |