Other Network Architecture Subjects

Hello,is it possible to rate-limit traffic on next-hop value? Something like to:int ATM1/0.150 point-to-pointip address 192.168.0.1 255.255.255.252pvc 0/150[ ... ]!ip route 192.168.1.1 255.255.255.255 192.168.0.2ip route 192.168.1.2 255.255.255.255 1...

Hi, ciscoworks 2000 running on nt, rme ver 3.4, cd 1 5th edition.i can generate a bugs report for all my devices but when i try and browse the bugs via the 'catastrophic, severe or all option' it responds ''Bugs summary is not available for this imag...

I have an ethernet interface on a branch router using the Secondary command. I want the clients on that logical network to have their DHCP discovery broadcasts forwarded accross that router to a remote DHCP server.WIll forwarding broadcast work for ...

Hi, I am going to install some NM-AIC-64 on 3640 routers..I would like to test the alarm collect on our LAB before installing on customer site.Really the operational mode of this NM-AIC-64 and AIC-SGL-PNL patch panel is not very clear for me..How cou...

Hi, I have two 4506 and there is a check point nokia for filtring access to the production zoneWhen we do any ftp from our LAN to THE server in THE other zone , the utilisation of core became very high and some times the core is inaccessible. However...

I have a cisco 2611xm router with the serial number of JMX0649L2HX on the gear pannel, but when I access the cli ,use show version and show diag command , the PCB Serial Number is JAD06480SJC (1593977455)-display of show diag, Processor board ID JAD0...

we created some sub-interface on the 7500 serier router. after a running time , there is a problem in vlans. example interface FastEthernet4/0/0.3 encapsulation dot1Q 20 ip address 10.1.19.9 255.255.255.248 ...

I am wondering if a network interface on a Cisco 2600 can have two IP addresses on the same network. For example, can two subinterfaces on a physical network interface have these IP addresses 192.168.1.1/24 and 192.168.1.2/24? Can it be accomplished ...

A 2611 router with a serial interface (non-isdn). Can I connect it to a ISDN line using a ISDN Terminal Adapter? In this case the router (TE2 device) connects to the ISDN TA which in turn connects to the ISDN network. If the configuration is possible...

I have a customer with two 1700 Routers connecting their remote offices. Both routers configured for both IP and IPX Networks. IP network is up all the time. while IPX network is not. The server at each location will lose connectivity ever couple ho...

Is there a command to show the "Chassis" serial number off a remote router.Please no "Show Version" responses, that is the number one response I have gotten and it is not good for "Chassis" serial number.

Hi,Is their a command to find out the serial number of power module in cat 4006 switch and also ios 4006 switch.regards,shashank

how i can filter mac address in a ethernet interface, permiting only one mac address and deny any other, thanks in advanced

what is going on down at the bottom and how can i stop it?%Error opening tftp://255.255.255.255/network-confg (Timed out)%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)%Error opening tftp://255.255.255.255/router-confg (Timed out)%Erro...

I have a 6509 (MSFC2) runing native (IOS) mode with 12.1(11b)E4. I am connected via 100Mbps Dot1q L2 trunking to a non Cisco service provider. I am using several VLAN's and the service provide is 'policing' each VLAN to 10Mbps inbound into his equip...