Resolved! IS-IS: L1L2 Router
Hi:Is it possible to have a L1L2 router connected to two different areas at the same time?Theory says that all ISO areas are like OSPF stub areas, please clarify.
Hi:Is it possible to have a L1L2 router connected to two different areas at the same time?Theory says that all ISO areas are like OSPF stub areas, please clarify.
Hello,I am using an 1721 to connection to a central router. When I try to establish an no call is made. A packet is routed to the dialer interface and mark as interesting traffic but I think the router cannot bind the dialer to a physical interface.D...
Hello,I have a cluster with two 2950 using GigaStack Gbics, in one port per switch. spanning-tree stack-port is configured on that links.The second port on the access switches is used as uplink to the core switches. When I try to extend the cluster w...
Hi Friends, I need guidance regarding VLANs on L2 Switches(2950 Model).If I create VLANs on these How do they talk to each other. I have a 2600 Model Router. Suppose I create 3 VLANs on a Switch how are these 3 going to talk ...
Hello,10 minutes after the installation of a new 2950-24 with IOS12.1(11)EA,we got this error message :SCHAN ERROR INTR: unit=0 SRC=6 DST=5 OPCODE=20 ERRCODE=5We loose all network connections,all traffics. After reboot + 10 Minute...
Hi,I have a router 2620 and i want to give him some priority on some flow. So i decide to use the priority-list command, but that don't seem to be good. I try to use a netmeeting between 2 compueter. For see if it's work i launch a some ftp for tes...
Hi All,My company thinking use 3725 router to replace its old 4000 router. I saw there is a 36-port Etherswitch network module can be used in 3725. Does anybody know if all the ports of the module can be used for routing (and can assign an ip address...
I have just seen the following config on a customers 3550 and would like to know what the "switchport access vlan 110" command does as the links are supposed to be dot1q trunks!interface GigabitEthernet0/3 switchport access vlan 110 switchport trunk ...
Can anybody tell me how you configure an async line to display a host menu once connected ? e.g. 1. Host A 2. Host B 3. Host C.We have a support company that uses the ATDT command via a terminal emulator, but once they connect all they get is a load ...
Hi,Anyone knows how to use hyperterminal for configuration, using notebooks/laptops without serial interface?Thanks,
Current SetupA remote office D is connected to Headoffice L. I have a Nortel Router at D, the serial interface (ppp) links to Head office. LAN1 is token ring and I have 5 departments (total 30 users) connected to tokenring. LAN2 is 100meg ethernet in...
We have a typical type of scenario where customer has 30 differrent remote branches to be terminated to the central router.Omantel ( Service provider ) has suggested a channelised E1 leased line to the customer which will accomodate all the 30 branc...
Hi all,I have following network diagram,Router1(2651XM)|switch1(2950) -- VLAN1 |VLAN2 -- router2 (pc) -- LAN3Router1 and switch1 are configured as router on a stick config (with VLAN1 & VLAN2). Another PC(acts like router2 to LAN3) is being added.A ...
What actually happens when a packet is dropped on the internetwork ? What does the term "drop" exactly mean ?Is the packet extinguished/destroyed in any way ?
I have a dial-up connection thru telephone at my home..Whenever I connect to the internet thru dial-up over telephone line, I get the following output for "ipconfig" and "ping" on the DOS Command prompt.The command fired and output is as follows:Wind...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |