Hi All,How do I configure LMS 2.1 to support snmp ver 3.0? When I configure snmp ver 3.0 on switches and I cannot connect from LMS now. Please advise me.Thanks
Hi All,How do I configure LMS 2.1 to support snmp ver 3.0? When I configure snmp ver 3.0 on switches and I cannot connect from LMS now. Please advise me.Thanks
I know this is no longer supported, but does anybody know where and how I can get a copy of this software?Thanks.
Is there a way to insure that each port on a 3550 will only allow DHCP to issue one pre-determined IP address? I will not know the MAC addresses in advance either. The 3550 is in a student housing building. The students are only here for a short a...
I have 2 7513's in my core with ATM DS3 attached, connecting remote offices using Frame-Relay Internetworking. 2 PVC's are mapped to the 2 7513's, one is primary the other is for backup. If I shut any of the connections the other end doesn't see it...
Hello,I tried to connect two 3662 Router serial back-to-back together. I used on both sides NM-4T and IOS 12.1(5)T12. One router connected a serial DCE-Cable, one with a serial DTE-Cable. I set the clock rate and keepalive were on. But on both sides ...
All the ports in my 3548 are configured to vlan 7. With spantree portfast enabled.1. User complained that he is unable to get the ip address dynamically.2. checked the spanning tree for that interface it show spanning tree down.3. Changed the vlan to...
Hi,I would like to use a router 1605-R to share a dial-up connection to the internet. This router has an ethernet port which I can configure easily. It's also got a serial interface to which is connected an analog modem via a DTE RS-232 - DB60 cable....
we have a pa-4e1 module in one slot of vip2-40. Just using tow ports, but there are nearly 100 subinterfaces every port(using frame-relay), so totoly nearly 200 subinterfaces. erverything works well. but when we reload the router, too many interface ...
How do i check whether my sub-interface is conigured as a part of IEEE 802.10? Actually I wanted to assign an ip address to a sub-interface.
How do I enable Internet Protocol processing on a subinterface?
hello all,I have 2 * 2620's and I am trying to connect them via their serial wics to run ospf. I have set them up in a lab and I am trying to connect over a constantly up isdn connection. This is done using 2 * adtran terminal adapters and the 'diale...
We are trying to upgrade a Ciscoworks 2000 (windows version) from LMS2.0 to LMS2.1.When we try to execute the command cwjava -cw "C:\program files\CSCOPx" com.cisco.nm.cmf.jrm.disablejobs we have the following error message: JAVA_COMPILER=NONE in CW2...
I have set up a test environment, with to routers connected to each other serial interface though a back-to-back cable. I have set the clockrate on the DCE end. I'd like to know, if it is somehow possible to see the assigned clockrate on the DTE end ...
Hi,i got this little prob with a 3550 switch.I made 3 vlans an it vlan 1 10.71.32.2 255.255.252.0 Vlan 20 10.71.48.1 255.255.254.0 and Vlan 30 10.71.60.1 255.255.255.0 now i need another ip address connected to vlan 1 but i still need to keep the o...
I cannot get multilink callback to work to Windows Clients (2000 & XP, have not tried others). The clients can call in with 2 B Channels to a PRI or BRI but callback will not bring up a 2nd channel. I do not see anyplace where the client can be confi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |