What is the maximum acceptable level of collisions on an ethernet interface (running half dulpex) as a ratio of packets throughput?
What is the maximum acceptable level of collisions on an ethernet interface (running half dulpex) as a ratio of packets throughput?
Anyone know what are the commands needed to configure the chassis ID on a CatIOS switch? That is I'm looking for something equivalent to the command "snmp chassis-id" on an IOS switch/router. Thanks in advance.
Who can I deny telnet to my router?
I have a AS5248 with dual T1/PRI. We have a T1 PRI that is going to have only 12 lines working. I need to configure it that way....how? I have 11.3 ios
I accidentally erased my flash on a 1720 router. I have the IOS CD, and Ican xmodem the image to the router. After the image decrompresses, I caneven configure the router. However, when I reboot, I go back to the RoMmonscreen. I have my register set ...
I need the ability to have a 2948G-L3 perform Layer 2 VLANS, perform Inter-VLAN routing and HSRP for the Inter-VLAN routing. There will be a second 2948G-L3 for the HSRP partner. Is the config below correct and the best way to do this? Thanks.bridge ...
What the may defference of WS-6148-RJ45V & ws-6348-RJ45V ,because the listprice is defference..
I've got a client that changed the subnet mask of his class C network to 255.255.252.0. It was 255.255.255.0. The address range that we were using was 192.168.253.1 - 192.168.253.254. Now the client is trying to use the 192.168.252.1 - 192.168.255...
I have that in my router but I want to remove it.ip local pool default 10.10.3.112 10.10.3.115Who can I do that?
Now, that we hace archived the running-config of our Cat 5500 using RME 3.4, it created a bunch of folders, named 31 through 43, where, supposedly it stored these configs. How do I find out which configs are stored in what folders?Thanks.- Alex
My Question is will re-convergance of EIGRP after route SIA cause any packet loss(or connection loss) for applications like telnet or FTP?Background: (1)My network is experiencing EIGRP SIA with neighbor resets( about every 35 to 45 minutes). ...
I have this 7120 router which seems to be okay, but when I type "Sh Ver" I get this output.120#sh verCisco Internetwork Operating System SoftwareIOS (tm) EGR Software (C7100-IS56I-M), Version 12.1(5)T9, RELEASE SOFTWARE (fc1)TAC Support: http://www....
Are there any circumstances in PIM-SM where a non-DR router on a multi-access network will process an IGMP Membership report and forward the "join" message up to the RP? Pardon the ascii-art below (R2 is the DR for both of his interfaces), but what...
running rme 3.4dfm 1.2cm 3.21) When I view the net. topology it shows a '?' for my 2620's. Also, the 2620 isn't showing up on the right side of the view. It shows 72xx's, 2950's, etc. but no 2620. How do I change that.2) Some T1 links on network t...
I am looking for the way(if possible) to get a UBR900 series to pull a dynamic public IP and NAT it to private IP's on a UBR provisioned for one dynamic IP. I use these all the time to run static IP LANS, but have never set one up to pull a DHCP IP ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |