Hi! I have a group of Catalyst 3550 SMI switches, i was planning to upgrade those switches from SMI to EMI Image, i know i have to purchase an upgrade kit to to this, but, Would it be possible to upgrade more than 1 switch just with one upgrade kit?
Hi! I have a group of Catalyst 3550 SMI switches, i was planning to upgrade those switches from SMI to EMI Image, i know i have to purchase an upgrade kit to to this, but, Would it be possible to upgrade more than 1 switch just with one upgrade kit?
Hi we have several switches 5500s and 6500s with software versions 5.1 to 5.2. Now, we are planning for upgrading the switch sofwtares to IOS 12.2. One problem that I foresee is that the commands in the old version of software were set-based while th...
I have a WS4014 Sup III engine in the 4006 box. All along i thought 4006 is CLI based, but this one is a IOS based. Been trying to find info on how to get the routing done between VLANs but can't find one. Can anyone point me to the right direction?
since the 806 router dosn't have an AUX port, can I dial-in to the console port? If not, how do I go about configuring it remotely if the line fails
I am looking for a dialup Configuration for router with high speed serial link.
Question :Can anyone explain to a layman (me), how the Master Browser works on a LAN with multiple switches (5500 family) setup as VLANS in a N.T. environment ?
i'm trying to enable qos on a 6509 and I am not sure when to use port based or vlan based qos. currently i have a 16 gigabit port module, and each port is configured with a 2 vlans (voice and data) and is a trunk port. i'm trying to do qos based on i...
What is the best way to converge two networks that private IP's overlap? Nat or Pat, other method? This is a temporary setup(10 weeks) until they are physically combined. They will be linked by a T1. Lete me know your ideas, done this before?
I currently have implemented two T1 Private Line clear channel IP T's to the Internet, running BGP Protocol. There are two routers which terminate the two T's, and two Cisco 2600's used for loadbalancing the outbound traffic. Behind the two load ba...
I have a 2621 router with 64Mb DRAM and 16 Mb Flash. The IOS version is 12.1 (5)T7 softare option c2600-IS-M. My goal is to limit bandwidth based upon IP address. The server IPs will be on interface F0/1 and the Internet will be on interface F0/0. I'...
I am trying to delete ( remove ) IMA group interface from my Cisco 7500 Router but I got the following error message :CORE#1(config)#no interface atm 4/1/ima1% Removal of physical interfaces is not permittedCORE#1(config)#There is no port configured ...
I've read through the documentation but I'm still not clear on one issue: Can Device Fault Manager send e-mail or pager alerts on its own without sending them through a separate NMS?
Is there a possible way to log messages of certain severity levels in the memory buffer and send messages of different severity to the syslog server.For e.g is it possible that messages of severity levels 3,2,1,0 only gets logged in the router buffer...
I am using a Cisco 3661 router with IOS version 12.2(4)T. My problem is that everytime the router is rebooted I have to reconfigure the system clock because it resets to Feb 28. I correctly configure the clock and write the changes to NVRAM. Is there...
Hi all,I have a 6509 with 4 VLANs defined and routed via the MSFC2 cards.I need to create 2 new VLANs, but I should use an external 4700 to route between them.The 6509 has CatOS 6.1(2), the 4700 has IOS 11.3(11b)T1 and only ethernet interfaces.If I'm...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |