Other Network Architecture Subjects

I have 4 3550 switches clustered and have just purchase a new 3550. I dont want to add this new switch to the clust but want to link the switches so that I can see the rest of the network. ie the equivalent to pressing the uplink button on a cheaper ...

Dear sir/Madam, I have installed two cat 3550 for our new implement projects on win2k file server cluster. Since the cluster server need to reserve some fixed ip for public and hard-beat newtwork, the question come , if somebody manually in...

I need to configure a Cisco router model 3640 using NAT, as the description below:All packets from one specific network must use the internet interface as inbound and outbound before reaching the target, at first it seems to be a not necessary hop, b...

Having some config problems, can not seem to get it to work i have a 1605 Cisco router, and i would like to use it to connect my lan to the cable modem is it posible without extra hardware, if so what hardware would i need.

I am trying to get fastetherchannel (200mb) running between a 7507 (12.1.7e) and a 7204 VXR (12.2.10b) and I keep loosing my duplex settings on both sides when there is a cable loss problem. any ideas?Also I am trying with between the 7507/7204 and a...

I can establish remote access to my as5300 via analog, isdn or using my cell phone as a modem(analog mode) without any problems.Cell phones with the 1x(cdma) chip provides connectivity via data packet.Does the AS5300 support this technology?If yes, ...

I have a router 3640. There are two E1 boards connected in this equpament, therefore I have several wans. There are multiple NATs configured on this equipament already, so the ethernet port is the outside interface and I cannot change this configurat...

2 Cisco 3640's running IOS 12.2.(5b) connected via 3 T-1 circuits. All 3 circuits configured into a single multilink bundle. "ppp multilink fragment-delay" not configured. Frames larger than 82 bytes are fragmented for sending across the multilink...

How can I enable debounce on a Catalyst 2980G-A switch.Switch has CatOS ver 6.3(4)I know the command is set port debounce <mod/port> enableHowever, the switch does not recognize this command even though in the default config it is set port d...

we have 3640 router and I want to load new ios using tftp server. but the router is giving an error..Router#copy tftp flashAddress or name of remote host []? 10.15.45.83Source filename []? c3640-i-mz.122-7c.binDestination filename [c3640-i-mz.122-7c...

Hi,We are about to build an ethernet network for about a 100 home users.I would like to have the ability to lock ports on swithes to a single ip address so if the clients change their ip address they cant get anywhere. Also broadcast control is impor...

I purchashed a Cisco 806 router w/32 MB and the Firewall Feature Set. It is doing NAT, RIP, and IP forwarding of RDP traffic to a Windows 2000 Terminal Server. The users in the office can initially access the Internet, however, when several of thes...

I have HSRP configuration in Catalyst 6513. For any VLAN interface we have configured 3 IP addresses: one for active router, one for standby router and another one virtual IP address.I dont have a DHCP policy for entire whole network. One workstation...

can i connect the ports of the x4124-fx-mtrj module of a distribution switch (4006) to the GBIC ports of an access switch (3550) orin another way if i want to connect 20 GBIC ports from 10 switches (3550) to a 4006 switch ... can they be connected to...

I have remote access router 2660,and Cisco secure ACS 2.6.If the client has windows 95,98 or millennium he can get IP address but he cannot even ping his gateway and he cannot access anything in the network,when Iupgrade the client operating system...