Hi,On Cat4000, we can configure it to only allow specifc host to logon thru telnet. e.g set ip perm <host> telnet. Does Cat3500 or Cat2900 switch (L2 only) support this feature ? Thanks in advance.Rgds,Ivan Cheng
Hi,On Cat4000, we can configure it to only allow specifc host to logon thru telnet. e.g set ip perm <host> telnet. Does Cat3500 or Cat2900 switch (L2 only) support this feature ? Thanks in advance.Rgds,Ivan Cheng
I am investigating using the following config;map-class frame-relay 256K_CIR_PVC frame-relay traffic-rate 256000 512000 frame-relay adaptive-shaping interface-congestion 0 frame-relay fair-queueAnd then this config on the main interface;frame-relay t...
How do I place a priority on a bri interface so that the same channel is the first and only permanent connection and the others DOD.
Is there a ratio that ATM circuits should be limited to. On most interfaces it says maximum of 511 VC's, then gives your current configured. I guess this would really depend on the bandwidth you have.Thanks for the help,
Hi,I have installed Ciscoworks VPN Management bundle(CD 1 and CD 2). I am able to start ciscoview service.I am unable to obtain the network topology from this base software. Pls suggest me should i install any other modules to obtain the result.regar...
Dear Cisco'ers,I am trying to attach a third-party IDS to CISCO 2950 and toport-mirroring:cisco2950(config)# monitor session 1 source interface Fa0/4cisco2950(config)# monitor session 1 destination interface Fa0/2now the problem is that this automati...
i am suppose to deploy 100 user campus network in a hall within a buiding using cisco swithches ,i wonder the type of swithch i will use for this ,the client wants a 1:1 redundancy on the critical path ,pls advice
Hi there,I'm looking for a Mux or similar device that I can connect to a PRI and split out several BRI's for seperate connections to routers and video equipment. I've found the Adtran Atlas 550 will do this, but was wondering if anyone knew of a chea...
Hi ,I have a ISDN dial up configured on the Router and I require a simple configuration to be done which I am finding a small problem with , Ihope you could please suggest me a solution to it.The requirement is that with the command Access list 110 ...
We have 3500XL, 2950G series switch."spanning-tree portfast" is STP disable? or STP enable?spanning-tree portfast has not two forwarding delaytherefore, spanning-tree portfast disable STP.My opinion is correct or wrong?
In this scenario Cisco 2500 connected to several remotes via Frame Relay. One of the locations is experiencing bandwidth issues where FTP / or large e-mail attachments will starve the main application which is Telnet based. The default WFQ settings...
Hi, sirThere is cisco7204 with NPE150.System Bootstrap, Version 11.1(5) [mkamson 5], RELEASE SOFTWARE (fc1)C7200 processor with 49152 Kbytes of main memoryIOS (tm) 7200 Software (C7200-IS56I-M), Version 12.1(15), RELEASE SOFTWARE (fc1)Slot 3 with PA-...
Can anyone recommend good references, links, regarding optimizing the use of DDR interface-dialer properties?Thnx.
Hi All,I am enabling RBE bridging for DSL on a Cisco 7513 router. Here is my sample config that I've drafted for it, for an ATM subinterface. My question is pretty striaghtforward: should this config work? If not, any suggestions, feedback, would ...
let say i have five 355o switches doing a half duplex gigastacking. 2 uplinks are used to attach from the top and bottom of the stack to the same distribution switch.Is it possible to configure it the 2 uplinks as gigaether channel so that both upli...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |