Is it possible to bridge Netbeui across VLAN's, we have a server that only talks Netbeui on one VLAN and workstations that have to access this server on another VLAN. Is this possible with a cisco switch, if so how?
Is it possible to bridge Netbeui across VLAN's, we have a server that only talks Netbeui on one VLAN and workstations that have to access this server on another VLAN. Is this possible with a cisco switch, if so how?
Applying an ACL to one of the VLANs on a 5513 has disabled all printing between this VLAN to others. The ACL is configured only to block port 161 SNMP, and allow everything else. Hence, the lines are as follows: access-list 111 deny udp any any eq sn...
Is there a way to manually tag routes in the v2 "Route Tag" field when redistributing from BGP vpnv4 address-family?Thanks,Tony
I have tried to connect directly two AUI ports of a 2514 router using a recommended cable (pins 3-5, 5-3, 10-12, 12-10; and 6 - 9 on each side).But the ethernet interfaces goes up and immediately down, this process is repeated continuously after a fe...
We have a required for adding around 100+ sites, all connected via 10Mbps LAN-extension services to our core network. Instead of placing a router at each remote site and performing edge-routing, we are considering moving the routing to the core of th...
I am trying to route all private IP address; 10.0.0.0 - 10.255.255.255, 172.16.0.0 -172.31.0.0 and 192.168.0.0 - 192.168.255.255 to null0. For 10.0.00/8 and 192.168.0.0/24 I used the mask of 255.0.0.0 and 255.255.255.0 But I am not sure of the mas...
Hello, I need to verify if usernames and passwords are needed for PAP Authentication? I know they are needed for Chap... but are they required for PAP?Txs for your help.Carlos.
hello,in my installation of lms 1.1 on solaris 2.6 i want to actualize the startup configs. how can i do this ?i have appr. 100 router in the ...out of sync report. after generating some jobs with netconfig to do a write mem, the number of ...out of ...
Hello,I am going to replace a Bay Network Router to a Cisco Router in my network. However, I am no idea what is configuration in the Bay router. Any one can tell me how to show the configuraton in the Bay router?Andy
Hi all, Can anyone please explain the difference between null interface and loopback interface ?.. Kindly explain the significance of both in the routing point of view.. Thanks in advance....
Have been noticing "excessive" collisions on ethernet interface on the MC 3810 and the on the PIX's outside interface. These are directly connected to one another via a 2 ft cable.When traffic is going across this link, collisions register on both i...
Hello,I Would like to use 8 X.21 links at 2meg each on the 3745. (need 8 connectors)Regarding the configurator, I can use only 3 WIC2T >> 6 Links.So I have select NM-2Wand Added 2 additional WAN WICs.... But configuratorcomplain that only 3 WICs can...
We have DLSW using Border peers. What I need to know is - if I was to add another router (external router) to peer with our DLSW network does this router need to be part of a peer group or can I configure a local peer statement and a remote peer st...
i have a problem with using callback and normal dialup,i have 2611 router with the below config.i am using tacacs+ for authentication with ACS with windows version.in this i have 250 users from which i wana give callback facility to 50 users and rest...
when i insert my 4232-l3 in slot 2 or 3 of 4006,the POST is ok but i can't session into the layer 3 config mode.in 4,5,6 it's all ok.what's wrong with it?thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |