Other Network Architecture Subjects

With reference to Alonza-Garza's conversations (4006 RSM question WS-X4232-L3), I'm also trying to set up a Cat4006 (in a test area) with a layer 3 supy card (separate card) and I'm confused why there needs to be a 'native' Vlan for management purpos...

If you have a telnet session running to at router and jump with a telnet or SSH to another host. Is it then possible to log all information/commands going into that session??

Hopefully you can point out my mistakes here.I can ping the Extreme, but can't ping the 3500XL nor either server. All connections are 802.1q trunk links. The native VLANs for Server23 and Server24 are 23 and 24, respectfully. Sorry for all the x's......

I am setting up a VLAN lab but I have a question on the 4006 RSM configuration options. Assuming that my RSM is in MOD 2, I understand that from the SUP II's point of view it sees 2/1 and 2/2 connected because he see's the 2 "internal" Gig channels ...

whitch IOS version in the L3 (WS-X4232-L3) module of the catalyst 4006 support NAT

There is a template in RME->Configuration Management->NetConfig that allows you to change the enable password:set enablepass%OLDPASSWORD%************If I try to create my own template that changes both the user and priveleged mode passwords, using th...

I have CiscoWorks 2000 on my network. Every 4 hours, it collects inventory and configs from a pair of 7507 routers. When I view the router logs, I am getting SNMP CPU hog messages for the get next procedure. Apparently, CiscoWorks is causing perfo...

The cisco doc http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_c/wcdfrely.htm#xtocid7 says that when you configure static mapping, it will automatically disable the in-arp. but When I configured a static mapping in multipoi...

I have a Cat2948 running 5.5(2)with multiple vlans configured. I have 2 Intrusion detections systems that I would like to install on 2 of the vlans configured on this switch. Can I span one vlan to one span port and another vlan to a different span p...

I have 2 serial lines. one T1 and one 64kbps .When my T1 line gone down i want to route for my 56kbps line .I use static or default Routes .How i can implement this in my 2600 Router.Bart

Cisco has recently announced the new Sup III for the cat 4000 series. Does this Sup have Layer 3 routing as part of the card, or do I still need to purchase the 4232 L3 card? Is there any more information on this new Supervisor card that I can read...

We have a 7204VXR chassis with a NPE225 module together with a C7200-I/O-2FE/E port adaptor that has begun to fail to boot. I've pasted the console output that's displayed at boot below:System Bootstrap, Version 12.0(19991120:010612) [nlaw-conn_4xe_E...

I have a C2600 router. I wish to take packets entering from one link (ex. WAN link from ISP#1) and set them with a specific MPLS label, and take packets entering from another link (ex. WAN link from ISP#2) and set them with a different MPLS label, be...

Could anyone shed any light onto this? My colleagues and i have been having a discussion as to which is the best routing protocol to employ, OSPF or ISIS. We are an ISP and could not find any conclusive information leaning either way. Any input is ap...

All I want is internet connection for the next servers WWW, POP3, SMTP, VPN, and of course www clients.I can get a 2Mb/524Kb ADSL or a T1 (complete or fractional).The cost of the ADSL is 1/4 of the T1 (and I wont need a router), is there a reason why...